• RE: DLPC7540EVM: How to feed video signals via FPD-Link port to DLPC7540EVM

  

  made4engineering

  Sherman, how exactly are you connecting the OM13561 and DLPC7540EVM together? What ports?

  • 9 days ago
  • DLP®︎ products
  • DLP products forum

• DLPC7540EVM: DLPC7540EVM Is it possible to send I2C commands over the USB Interface?

  

  Paul Sluis

  Part Number: DLPC7540EVM Other Parts Discussed in Thread: DLPC7540 Hi, I am a bit confused about how to use the DLPC7540EVM. If I want to send an I2C command do I need some additional hardware connection or can I send the command over USB? What I am trying…

  • 22 days ago
  • DLP®︎ products
  • DLP products forum

• DLPC7540EVM: Trigger In Port

  

  TI-CSC

  TI Thinks Resolved

  Part Number: DLPC7540EVM Other Parts Discussed in Thread: DLP650TEEVM , DLPC7540 , DLP650TE Hello E2E Experts, Good day. I am trying to let the DLP6540TEEVM present a prestored pattern when DLPC7540EVM receives a trigger signal. Then, when receiving another…

  • 1 month ago
  • DLP®︎ products
  • DLP products forum

• RE: DLPC7540EVM: Unsuccessful connection from DLPC7540EVM to computer

  

  Fizix

  Hello Zhiyu, I often answer the DLPLCR65EVM questions. Please allow a little time for us to discuss this here and one of us will respond to your latest inquiry today or tomorrow at the latest. Fizix

  • 3 months ago
  • DLP®︎ products
  • DLP products forum

• RE: DLPC7540EVM: Unsuccessful connection from DLPC7540EVM to computer

  

  made4engineering

  Check to make sure the flex cables are connected properly and that there are no physical problems with the connectors. You will need to provide video input through a front end using mode 0x0-Disp External

  • 3 months ago
  • DLP®︎ products
  • DLP products forum
Answered

• RE: DLPC7540EVM: Out of box failure of evaluation board.

  

  Paul Sluis

  Resolved

  Hi Venkata, The Invalidate Settings didn't change anything, but the second step Calibration - Manual Warping fixed the problem! Thank you very much, I would never have been able to fix this on my own. Thanks, Paul

  • 1 month ago
  • DLP®︎ products
  • DLP products forum
Answered

• RE: DLPC7540EVM: Device cannot be detected anymore

  

  Miha Markocic

  Resolved

  Hi! We managed to update the firmware successfully. We used another PC with the software running in advanced mode, connected to the command interface using USB connection and in the "flash program" selected "skip bootloader" option only. (the jumper was…

  • 2 months ago
  • DLP®︎ products
  • DLP products forum
Answered

• TPS65145: I based a design off of the DLPC7540EVM, and the TPS65145 doesn't always startup properly

  

  Paul Sluis

  Resolved

  Part Number: TPS65145 Other Parts Discussed in Thread: DLPC7540EVM , DLP650TEEVM In my design I implemented the voltage Tripler configuration as per the reference design, and the 16V supply goes to 18.5V. When I make the correction to set the board as…

  • Resolved

  • 1 month ago
  • Power management
  • Power management forum
Answered

• RE: DLPC7540EVM: JTAG Flash Programmer - seems like the Flash Bootloader binary file is missing

  

  made4engineering

  Resolved

  Closing this thread. If you continue to have issues, please repost

  • 1 month ago
  • DLP®︎ products
  • DLP products forum

• RE: DLPC7540EVM: Install firmware without USB connection

  

  Jonathan Navor

  Hi Made4engineering, Thank you for waiting. The customer had been unable to connect via UART and would need some more advice. However, without making any changes (as far as we can tell), the firmware was able to successfully upload while we tried to get…

  • 3 months ago
  • DLP®︎ products
  • DLP products forum

Didn't find what you are looking for? Post a new question.