• 

  Annie Liu

  • 4 months ago
  • Sensors
  • Sensors forum

  DRV5033: Questions about Bop, Brp, and Bhys

  TI Thinks Resolved

  Part Number: DRV5033 Hi team, The customer is experiencing below issue and needs your help. On the sixth page of the manual, Bop MIN=±1.8mT TYP=±3.5mT, MAX=±6.8mT. Brp MIN=±0.5mT TYP=±2mT, MAX=±4.2mT...
• 

  Kengo.Y

  • 9 months ago
  • Sensors
  • Sensors forum

  DRV5033: About samples with magnetic property data.

  • Resolved

  Part Number: DRV5033 Hi team. My customer needs the samples with magnetic property data
• 

  user5541778

  • 10 months ago
  • Sensors
  • Sensors forum

  DRV5033: Reliability test

  • Resolved

  Part Number: DRV5033 Hello, Please let me know what kind of reliability test was carried out
• 

  Meng jeffrey

  • 9 months ago
  • Sensors
  • Sensors forum

  DRV5033: Use only the N pole for operation confirmation

  Part Number: DRV5033 1. Using the DRV5033 sensor device, the N and S poles are close to each other, and both act the same. 2. When the chip is assembled into the circuit, if only the N pole is used to confirm the operation, can it be determined that the...
• 

  Arnold Sachse

  • over 1 year ago
  • Sensors
  • Sensors forum

  DRV5033: DRV5033

  TI Thinks Resolved

  Part Number: DRV5033 We are using the DRV5033 in TO92 case hall sensor on a project, the problem is that each sensor switches at a different height from the magnet (within a 5mm difference). We have set up a jig so that the only variable is the hall sensor...
• 

  Jiandong Liu

  • over 1 year ago
  • Sensors
  • Sensors forum

  DRV5033: DRV5033 use as limit switch on 3D printer

  TI Thinks Resolved

  Part Number: DRV5033 Hi, My customer hopes to use DRV5033 to replace mechanical limits in 3D printer. However, customer worries that the B-fied of all magnets cannot be consistent, so customer need to test/adjust the position of magnets on 3D printers...
• 

  Sergey Zevelev57

  • 4 months ago
  • Sensors
  • Sensors forum

  RE: DRV5032: DRV5032AJ

  Scott I have tested Rdson at current within (5 -10)mA for 5 sensors DRV5032AJ. Results are: 14.887, 14.394, 12.178, 13.648, 13.272 Ohm . So, I can to suggest, that Rdson typical value =22 Ohm as for DRV5033. Maximum current is limited by power dissipation...
• 

  Y.Ottey

  • over 1 year ago
  • Sensors
  • Sensors forum

  DRV5033: Output voltage falls for a moment

  TI Thinks Resolved

  Part Number: DRV5033 Dear all, Our customer would like to know the cause of following phenomenon. When the power supply voltage is changed from 2.8V to 3.3V in the DRV5033DU, The voltage of OUT terminal (No.2 pin) falls for a moment like figure...
• 

  WU YISYUAN

  • over 1 year ago
  • Sensors
  • Sensors forum

  DRV5033: Hall sensing distance

  TI Thinks Resolved

  Part Number: DRV5033 Hi, The magnet has a conduction state close to the Hall. Stay away from the Hall and have an open circuit. Is this threshold value defined in the actual application? thanks.
• 

  WU YISYUAN

  • over 1 year ago
  • Sensors
  • Sensors forum

  DRV5033: Application consultation

  • Resolved

  Part Number: DRV5033 Hi team, I have one question in using DRV5033 : If the magnet is sensed

Didn't find what you are looking for? Post a new question.

• Ask a new question