TI E2E support forums
TI E2E support forums
  • User
  • Site
  • Search
  • User
  • E2E™ design support >
  • Forums
    • Amplifiers
    • API solutions
    • Audio
    • Clock & timing
    • Data converters
    • DLP® products
    • Interface
    • Isolation
    • Logic
    • Microcontrollers
    • Motor drivers
    • Power management
    • Processors
    • RF & microwave
    • Sensors
    • Site support
    • Switches & multiplexers
    • Tools
    • Wireless connectivity
    • Archived forums
    • Archived groups
  • Technical articles
  • TI training
    • Tech days
    • Online training
    • Live events
    • Power Supply Design Seminar
  • Getting started
  • 简体中文
  • More
  • Cancel


Search tips
Showing 24 results View by: Thread Post Sort by
    Answered
  • DRV592: HLQFP Package dimensions

    KKF
    KKF
    Resolved
    Part Number: DRV592 Hi, Can you provide the DRV592VFP package information please? It is not included in the datasheet (PDF) or the package drawing HLQFP (VFP) | 32 . Thank You & Best Regards, KF
    • Resolved
    • 9 months ago
    • Audio
    • Audio forum
  • DRV592: Overcurrent protection tripped

    Danny Chen1
    Danny Chen1
    Part Number: DRV592 Hello, I am current using the DRV592 to drive a peltier chip for cooling, CUI CP40347, however I am constantly getting the overcurrent fault. The supplied voltage is 5V but measured at 4.96V to be exact. The applied PWM is at 100kHz…
    • over 4 years ago
    • Audio
    • Audio forum
  • DRV592: Using DRV592 as a TEC driver - Keep getting FAULT0,0 (overcurrent) when using 5.5V as PVDD

    Dan Doran
    Dan Doran
    Part Number: DRV592 We're trying to use a DRV592 H-Bridge driver to drive a 2A TEC cooler for a laser diode, which we measure as a nominal 1.3 Ohm impedance. We're also using the circuit shown on the datasheet front page and on the Eval board schematic…
    • over 5 years ago
    • Audio
    • Audio forum
  • Answered
  • DRV592: Driving Peltier Element

    Bojan Jovanovic
    Bojan Jovanovic
    Resolved
    Part Number: DRV592 Other Parts Discussed in Thread: DRV594 , , DRV593 Hello there. We plan to use Peltier Element in our application to keep the temperature in the desired range. When the temperature is above a certain limit (e.g. 50C), we would…
    • Resolved
    • over 5 years ago
    • Audio
    • Audio forum
  • DRV592: PWM frequency & duty-cycle

    Markus Nenonen
    Markus Nenonen
    TI Thinks Resolved
    Part Number: DRV592 Hi, DRV592 has maximum PWM frequency of 1MHz. If I use 1MHz PWM signal can duty-cycle for this part be less than 50%? Or does internal FETs require minimum 500ns control signal in order to turn on? Can for example 1% duty-cycle be…
    • over 6 years ago
    • Audio
    • Audio forum
  • DRV592 evaluation module needed

    shawn mccaslin
    shawn mccaslin
    Other Parts Discussed in Thread: DRV592 I need a DRV592 evaluation module. Oddly, the DRV592 is still an active TI product, but they have discontinued the EVM for that part. How might I acquire a DRV592 evaluation module?
    • over 10 years ago
    • Motor drivers
    • Motor drivers forum
  • DRV592 FAULT0 ACTIVE

    Kamal Najmi
    Kamal Najmi
    Other Parts Discussed in Thread: DRV592 HI,please find below the feedback from my customer HD. I have another question about the DRV592 device. The DRV592 is now implemented in a printed circuit assembly and is operated within the nominal conditions…
    • over 10 years ago
    • Motor drivers
    • Motor drivers forum
  • DRV592

    Chris Fredricksen
    Chris Fredricksen
    Other Parts Discussed in Thread: DRV592 Hello, I am trying to use a DRV592 to drive a TEC module and getting too little voltage. The inputs are PWM outputs of an Atmel 328p at 1kHz. The impedance of the TEC module is ~265 mOhm and the TEC data sheet…
    • over 12 years ago
    • Motor drivers
    • Motor drivers forum
  • DRV592 operating temperature range

    William Mair
    William Mair
    TI Thinks Resolved
    Other Parts Discussed in Thread: DRV592 Hi I would like to operate the DRV592 over the military temperature range (-55 to +125 degC). The component datasheet states that it is only available in the industrial temperature range. Can the device be up…
    • over 13 years ago
    • Motor drivers
    • Motor drivers forum
  • Peltier Module Control Circuit

    YaD
    YaD
    TI Thinks Resolved
    Other Parts Discussed in Thread: DRV592 Hello All, We are working on a small peltier module control circuit : 3.8Vmax - 2Amax - 1.6Ohm Atfer runing some lab tests, we reached a compromise in operational parameters with a maximum current of 800mA…
    • over 4 years ago
    • Power management
    • Power management forum
>

Didn't find what you are looking for? Post a new question.

  • Ask a new question