• DRV8300-Q1: GVDD

  

  Sveinn Jia

  TI Thinks Resolved

  Part Number: DRV8300-Q1 Hi Team, In our system, we do not have a 12V power rail; we only have KL30, where the maximum voltage can reach up to 26V, which exceeds the absolute maximum rating of GVDD. Therefore, we plan to connect GVDD to 5.2V instead…

  • 3 months ago
  • Motor drivers
  • Motor drivers forum

• DRV8300-Q1: Simulation model

  

  PRAHLAD Supeda

  Part Number: DRV8300-Q1 Need DRV8300-Q1 simulation model.

  • 6 months ago
  • Motor drivers
  • Motor drivers forum

• DRV8300-Q1: TVS Diode rating for 48V system.

  

  Nihal kumar

  TI Thinks Resolved

  Part Number: DRV8300-Q1 Kindly help me in this topic, if I'm providing 48V to the mosfet, and based on the effect of bldc motor back emf how much TVS diode rating for input protection can allowed? Bldc motor, maximum speed is 1000rpm. Rated current…

  • 10 months ago
  • Motor drivers
  • Motor drivers forum

• DRV8300-Q1: Could one of leg be used for boost controller and rest of two legs be used for full bridge inverter circuit?

  

  Yoshiki Ochi

  TI Thinks Resolved

  Part Number: DRV8300-Q1 Other Parts Discussed in Thread: DRV8300 Hi team, Could one of leg be used for boost controller and rest of two legs be used for full bridge inverter circuit? Its boost ouput voltage is connected to full bridge inverter bus voltage…

  • 4 months ago
  • Motor drivers
  • Motor drivers forum

• DRV8300-Q1: Emission issues at 48-60MHz

  

  Praveen Ramaprasad

  TI Thinks Resolved

  Part Number: DRV8300-Q1 Tool/software: I currently use DRV8300-Q1 on my custom 1 channel BLDC motor driver. When tested for Radiated emissions, I have observed some peaks at 48MHz. When the motor is driven, only then this noise is observed, so i am…

  • over 1 year ago
  • Motor drivers
  • Motor drivers forum

• DRV8300-Q1：DRV8300DRGE ISSUE

  

  David Huang

  TI Thinks Resolved

  Part Number: DRV8300-Q1 Other Parts Discussed in Thread: DRV8300 Tool/software: SINGLE ESC GATE DRIVER.pdf Hello: Design Requirements: 1. Input Power: 12S Lithium Battery, approximately 40V-51V 2. Driving a BLDC Motor (output continuous current 60A…

  • 11 months ago
  • Motor drivers
  • Motor drivers forum

• DRV8300-Q1: The deadtime configuration problem

  

  Tommy

  TI Thinks Resolved

  Part Number: DRV8300-Q1 Tool/software: Hi E2E， We are verifying the design of the DRV8300-Q1 in a water-pump project. This is the output waveform of the high-side and low -side gate of the DRV8300-Q1 at open load. My question is: Why is there…

  • over 1 year ago
  • Motor drivers
  • Motor drivers forum
Answered

• DRV8300-Q1: Would like to disable deadtime and cross-conduction prevention

  

  Shunsuke Yamamoto

  Resolved

  Part Number: DRV8300-Q1 Other Parts Discussed in Thread: DRV8363-Q1 Tool/software: Hi team, Is it possible to disable deadtime and cross-conduction prevention? If not, are there any BLDC devices which don't have deadtime and cross-conduction prevention…

  • Resolved

  • over 1 year ago
  • Motor drivers
  • Motor drivers forum
Answered

• DRV8300-Q1: Is it possible to use motor driver as GPIO?

  

  JONGYEON BYEON

  Resolved

  Part Number: DRV8300-Q1 Other Parts Discussed in Thread: DRV8300 , DRV8328 Tool/software: Hello. I'm a DRV8300 three-phase motor driver The two phases are used to control the normal DC motor by PWM. I use GHA and GLA, GHB and GLB. My question is, if you…

  • Resolved

  • over 1 year ago
  • Motor drivers
  • Motor drivers forum

• DRV8300-Q1: EMC Circuit

  

  Renan Santos Adriano

  TI Thinks Resolved

  Part Number: DRV8300-Q1 Hello Team, Posting on behalf of my customer: I am currently working on a device DRV8300-Q1. Do you have any EMC Circuit for this device or any application guide I can check? Regards, Renan

  • over 3 years ago
  • Motor drivers
  • Motor drivers forum

Didn't find what you are looking for? Post a new question.