• 

  Li Chen92

  • 4 months ago
  • Motor drivers
  • Motor drivers forum

  DRV8353: DRV8353 Application

  • Resolved

  Part Number: DRV8353 Hi TI expert, May I know whether DRV8353 can be used for Servo Drives. Best
• 

  W Zwetsloot

  • 4 months ago
  • Motor drivers
  • Motor drivers forum

  DRV8353: Gate driver error while connecting DC motor

  TI Thinks Resolved

  Part Number: DRV8353 Hi all, For a DC motor drive application we're using the DRV8353S in independant PWM mode. We've got mosfets populated on the A and the B half bridge. On INHA our pwm is supplied while INLA and INHB are kept low and INLB...
• 

  Tom Fox1

  • 9 months ago
  • Interface
  • Interface forum

  DRV8353

  • Resolved

  I was originally too embarrassed to ask this on a forum but have decided to do so anyway. I have considerable experience in technology but not enough that I do not need to ask you this question: What exactly does TI do? I know you from the 60's as a maker of calculators and IC chips. Today, my interests...
• 

  user3549691

  • 6 months ago
  • Motor drivers
  • Motor drivers forum

  DRV8353: drv8353

  TI Thinks Resolved

  Part Number: DRV8353 DRV8353H in 3XPWM mode GHx output normal PWM and GLx output unusual PWM
• 

  Cole Macias

  • 3 months ago
  • Motor drivers
  • Motor drivers forum

  RE: CCS/DRV8353: Dose this driver support the MOSFET IPT015N10N5？

  Hello C hen, Thanks for posting on the Motor Drivers Forum! The Vth, VGS max, and VDS break down are all within similar specs to our device. The 40kHz PWM is below our max 200kHz spec. So, yes it will work. Doing the calculation for IDRIVE, I'd...
• 

  Wang Xiaoming

  • 4 months ago
  • Motor drivers
  • Motor drivers forum

  DRV8353: Over current protection behavior

  TI Thinks Resolved

  Part Number: DRV8353 Hi Team I notice there is a OCP_ACT setting in the Serial type to select turn off all three half-bridge or just the one detect overcurrent. but seems no detail about the behavior about hardware type. does hardware type only turn...
• 

  John11513

  • 4 months ago
  • Motor drivers
  • Motor drivers forum

  DRV8353: Can this part be used to drive BDC motor?

  TI Thinks Resolved

  Part Number: DRV8353 Hi experts, My customer's motor is 24V/20A BDC, though the supply voltage is not very high but considering back EMF they would like to use higher voltage device, our BDC driver cannot meet their requirement. They prefer 100V...
• 

  Jason Shen

  • 4 months ago
  • Motor drivers
  • Motor drivers forum

  DRV8353: VGLS pin not stable or damaged

  Part Number: DRV8353 Dears We have run the device with 120kHz PWM, with a Qg = 55nc MOSFET, and FOC BDLC control. and find that the VGLS have square wave with period of 400us and duty of 100us low. it is likely a protection of over load happened. so...
• 

  Adam Sidelsky

  • 4 months ago
  • Motor drivers
  • Motor drivers forum

  RE: DRV8353: DRV8353H : High Side Mosfet pins are damaged

  Yash, Sorry for the delay here, was this resolved? We do not recommend 100% duty cycle from start up with no ramp, even a small ramp would help to prevent damage. Regards, -Adam
• 

  Seokmin Hong

  • 6 months ago
  • Motor drivers
  • Motor drivers forum

  DRV8353: Question about PWM Noise and Bypass Capacitor of FET's Input

  • Resolved

  Part Number: DRV8353 Hi, I am using DRV8353 for motor driver system. . And found 20kHz PWM Noise

Didn't find what you are looking for? Post a new question.

• Ask a new question