Filter by Reset

All
Forums (477)
  • Motor drivers (398)
  • C2000™︎ microcontrollers (65)
  • Code Composer Studio™︎ (5)
  • Simulation, hardware & system... (4)
  • MSP low-power microcontr... (3)
  • Interface (1)
  • View all
Technical Articles (0)
Wikis (0)
Files (0)
Groups (0)
FAQ
  • Show only FAQs
Reply
  • Resolved
  • TI thinks resolved
  • Answer suggested
  • Has replies by TI employees
  • Has replies
Creation Date
  • Any
  • Past Week
  • Past Month
  • Past 3 Months
  • Past 6 Months
  • Past Year
From
To


Search tips
Showing 477 results View by: Thread Post Sort by

  • DRV8353RS-EVM: Sensorless MSPM0G3507 + DRV8353RS

    Part Number: DRV8353RS-EVM Other Parts Discussed in Thread: LP-MSPM0G3507 , SYSCONFIG Tool/software: Ladies and Gentlemen, I purchased LP-MSPM0G3507 and DRV8353Rx-EVM boards. When we move the motor we have to constantly change max current. From MSPM0…

  • DRV8353R: VDRAIN Slew Rate

    TI Thinks Resolved
    Part Number: DRV8353R Tool/software: Team, What's the purpose of this VDRAIN slew rate on design? Could you help to explain it more! very thanks. Regards Brian

  • DRV8353R: About the built-in power module LM5008

    TI Thinks Resolved
    Part Number: DRV8353R Other Parts Discussed in Thread: LM5008 Tool/software: Hi, Staff I'd like to inquire: ‌ If I disable the built-in power module LM5008 of DRV8353RS, will it affect the normal operation of DRV8353RS? Since the datasheet does not…

  • DRV8353RS-EVM: DRV8353RS IC footprint is not matching with the DRV8353RS evaluation board

    TI Thinks Resolved
    Part Number: DRV8353RS-EVM Tool/software: Hi, Why the DRV8353RS IC footprint (Centre pad) is not matching with the DRV8353RS evaluation board. DRV8353RS IC footprint from DRV8353RS evaluation board PCB layout design file. Any specific reason…

  • DRV8353R: The output issue for DRV8353

    Part Number: DRV8353R Tool/software: Hi, We use the DRV8353HRTAR for our new project, we tied the MODE to PGND for the “6x PWM Mode”, Now, the INHB input low voltage, but the GHB output is high voltage, can you help to review our schematic diagram…
    • Answered

  • DRV8353R: Low-Side Gate Driver Loop Layout

    Resolved
    Part Number: DRV8353R Tool/software: Hi TI, I found the low-side gate driver layout guideline in datasheet, which says I should minimize the loop from GLx -> LS gate -> LS source -> SPx. Also the layout guidelines of motor driver says: 1. Use thick…
    • Resolved

  • DRV8353RS-EVM: unable to see datawhen giving 12 volt supply

    Part Number: DRV8353RS-EVM Other Parts Discussed in Thread: DRV8353 I am currently working on interfacing the DRV8353RS gate driver with an STM32F407VGTX microcontroller using SPI communication. I am sending the 16-bit SPI command 0x1020 on the MOSI…

  • DRV8353R: DRV8353RHRGZ

    TI Thinks Resolved
    Part Number: DRV8353R Tool/software: We have selected DRV8353RHRGZ IC for Motor driving, to reduce the power losses uses three parallel Mosfet with single Gate driving pin e.g. Pin 8 (GHA) . the routing of this gate signal below attached image (highlighted…
    • Answered

  • DRV8353R: DRV8353RS phase to phase short-circuit protection damage

    Resolved
    Part Number: DRV8353R Other Parts Discussed in Thread: DRV8353 Tool/software: Hi Team! I have an issue with the DRV8353SR FET driver. The circuit requires short circuit protection. When I connect 2 phases the one low side gate driver is damaging permanently…
    • Resolved

  • DRV8353R: hall sensor supply voltage

    TI Thinks Resolved
    Part Number: DRV8353R Other Parts Discussed in Thread: DRV8353 , DRV8300 Tool/software: I want explore a BLDC Motor Typ QBL4208-61-04-013 with DRV8353Rx-EVM. The Motor need for Hall sensor supply +5VDC to +24VDC. The DRV8353Rx-EVM User’s Guide shows…
1 2 3 4 5 »

Didn't find what you are looking for? Post a new question.