TI E2E support forums
TI E2E support forums
  • User
  • Site
  • Search
  • User
  • E2E™ design support >
  • Forums
    • Amplifiers
    • API solutions
    • Audio
    • Clock & timing
    • Data converters
    • DLP® products
    • Interface
    • Isolation
    • Logic
    • Microcontrollers
    • Motor drivers
    • Power management
    • Processors
    • RF & microwave
    • Sensors
    • Site support
    • Switches & multiplexers
    • Tools
    • Wireless connectivity
    • Archived forums
    • Archived groups
  • Technical articles
  • TI training
    • Tech days
    • Online training
    • Live events
    • Power Supply Design Seminar
  • Getting started
  • 简体中文
  • More
  • Cancel

The TI E2E™ design support forums will undergo maintenance from July 11 to July 13. If you need design support during this time, open a new support request with our customer support center.



Search tips
Showing 25 results View by: Thread Post Sort by
    Answered
  • DRV8434AEVM: DRV8434AEVM

    Radostin Ognyanov
    Radostin Ognyanov
    Resolved
    Part Number: DRV8434AEVM Other Parts Discussed in Thread: DRV8434SEVM Tool/software: Hi, After intallation of the DRV8434SEVM GUI I got the following message: What could be the reason, please advise! Thank you!
    • Resolved
    • 10 days ago
    • Motor drivers
    • Motor drivers forum
  • RE: DRV8434AEVM: DRV8434A: TRQ_CNT 0V when stall in Torque count mode

    Murugavel4637
    Murugavel4637
    Hi Mats, Thanks for the update. The current waveform looks good. Mats Webjörn said: so still no explanation why nFAULT and STL_REP immediately goes low when nSLEEP goes high. The issue may be the high DCR of the motor coils 50 Ω. I think the torque count…
    • 8 days ago
    • Motor drivers
    • Motor drivers forum
  • Answered
  • DRV8434AEVM: Stall detection

    Shuhei Goto
    Shuhei Goto
    Resolved
    Part Number: DRV8434AEVM Tool/software: Hi team, I want to test Stall Detection. The following flow was executed. -Obtain a specific voltage in Learning mode -Turn unloaded motor in Torque count mode In this case, the voltage obtained in the Lerning mode…
    • Resolved
    • 1 month ago
    • Motor drivers
    • Motor drivers forum
  • Answered
  • DRV8434AEVM: EVM is not connected

    Shuhei Goto
    Shuhei Goto
    Resolved
    Part Number: DRV8434AEVM Tool/software: Hi team, In my condition, EVM is not identified by GUI. What is the cause of this? BTW, this matter occur in case of DRV84xx GUI too. The port is not identified. LED is blinking Best regards, Goto
    • Resolved
    • 1 month ago
    • Motor drivers
    • Motor drivers forum
  • Answered
  • RE: DRV8434AEVM: UI and Design Issues of DRV8434AEVM

    Murugavel4637
    Murugavel4637
    Resolved
    Hi Wang, wang sky said: My stepper motor is rotating 15 degrees on one pulse, why is there a 45 electrical angle? Thank you for this question. Electrical angle is the phase angle of the current waveform. See below representation. Square wave shown for…
    • 6 months ago
    • Motor drivers
    • Motor drivers forum
  • RE: DRV8434AEVM: Technical questions

    Murugavel4637
    Murugavel4637
    Hi Roy, The "Clear" button issues an nSLEEP reset pulse as described in the datasheet. Roy Chou1 said: When motor did the returning to zero action, we used the STALL signal to let MCU know the motor was back to point of original. Could you please…
    • 6 months ago
    • Motor drivers
    • Motor drivers forum
  • DRV8434AEVM: DRV8434AEVM software failure

    Rami Friedlander
    Rami Friedlander
    Part Number: DRV8434AEVM Other Parts Discussed in Thread: DRV8434EVM , , DRV8434A Tool/software: I installed DRV8434EVM software driver and enabled immediate execution at the end of the installation. In this case, the DRV84XX EVM software worked as expected…
    • 10 months ago
    • Motor drivers
    • Motor drivers forum
  • Answered
  • DRV8434AEVM: Software for DRV8434EVM on Windows10

    Rami Friedlander
    Rami Friedlander
    Resolved
    Part Number: DRV8434AEVM Other Parts Discussed in Thread: DRV8434EVM Tool/software: Hello, Where I can find the required software for DRV8434EVM on Windows10. I cannot install Windows11. Thanks in advance, Rami
    • Resolved
    • 10 months ago
    • Motor drivers
    • Motor drivers forum
  • RE: DRV8434AEVM: drv8432dkdevm user manual

    Jacob Thompson
    Jacob Thompson
    Hey Maik, Maik Staudt said: - 12V to GVDD and GND - Motorpower 0-52V to PVDD - The PWM-output 1 of the microcontroller to PWMA-Testpoint - The PWM-output 2 of the microcontroller to PWMB-Testpoint - The PWM-output 3 of the microcontroller to PWMC-Testp…
    • over 1 year ago
    • Motor drivers
    • Motor drivers forum
  • Answered
  • DRV8434AEVM: MSP430F2617 Source Code

    Mike Schell
    Mike Schell
    Resolved
    Part Number: DRV8434AEVM Other Parts Discussed in Thread: MSP430F2617 , DRV8434A Dear TI- I have installed the DRV8434AEVM. The evaluation board is working great! I really like the GUI; it's well-thought-out and easy to use. I am looking for a copy…
    • Resolved
    • over 1 year ago
    • Motor drivers
    • Motor drivers forum
>

Didn't find what you are looking for? Post a new question.

  • Ask a new question