Search tips
Showing 334 results View by: Thread Post Sort by
    Answered

  • DRV8701: DRV8701 with a higher Source/sink Current

    Resolved
    Part Number: DRV8701 Other Parts Discussed in Thread: DRV8251 , DRV8870 , DRV8770 Hello I am looking for a DC‑motor driver similar to the DRV8701 but with a much higher source/sink capability. The DRV8701 can only handle about 150 mA, and I need…
    • Resolved

  • DRV8701: DRV8701: Different supplies for VM and VBAT

    Part Number: DRV8701 Hello, I have some questions about operating DRV8701 and H-Bridge on separate supplies. In my application VM should be 24V and VBAT can vary between 0 – 28V. I always have 100% Duty Cycle. In table 9 the minimum voltage…

  • DRV8701: DRV8701 Blown

    Part Number: DRV8701 Hi Experts, Would you kindly help with the customer inquiry below? I have designed a BDC motor driver board that uses DRV8701 with Nexperia PSMN4R2-40VSHX FETs. Small numbers of these boards have been deployed to field and have…
    • Answered

  • DRV8701: Reading motor current on DRV8701

    Resolved
    Part Number: DRV8701 Tool/software: Hello I'm using DRV8701 and i want to read the motor current using ADC on my MCU. / Currently we drive the motor using fast decay (motor coasting). The datasheet specifies that SO is not valid during brake mode…
    • Resolved

  • DRV8701: Dynamically adjusting torque (current)

    TI Thinks Resolved
    Part Number: DRV8701 Hi everyone, Is it possible to dynamically adjust the current regulation (VREF) on the DRV8701 during operation control torque without using a microcontroller? If so, what is the simplest way to implement this in hardware (e.g…
    • Answered

  • DRV8701: PWM

    Resolved
    Part Number: DRV8701 Hi can you please confirm if single PWM can drive both High side and low side mosfet in Half bridge configuration
    • Resolved

  • DRV8701: To make gate current variable

    Part Number: DRV8701 Hi all, We are considering the introduction of DRV8701. Is it possible to get information on the following? 1) I want to change the gate current. How can I set it? 2) If the capacity is not enough, can I use a buffer circuit? …
    • Answered

  • DRV8701: nFAULT and nSLEEP

    Resolved
    Part Number: DRV8701 Hi, I found the following thread about the relationship between nFAULT and nSLEEP. https://e2e.ti.com/support/motor-drivers-group/motor-drivers/f/motor-drivers-forum/860380/drv8701-e-nfault-pin-active-1ms-when-turning-bridge-on…
    • Resolved

  • DRV8701: nFAULT

    Part Number: DRV8701 Hi, I am driving a BDC motor using the DRV8701. The nFAULT signal is asserted, and I am trying to find the cause. I would like to send the circuit diagram and waveforms via private message. Could someone please provide assistance…

  • DRV8701: EMC issue

    TI Thinks Resolved
    Part Number: DRV8701 Dear TI Engineer, We encountered the following two issues when using DRV8701 to drive a DC brushed motor: 1) SO pin waveform issue The pin definition in the datasheet requires no more than 1 nF of capacitance on this pin.…

Didn't find what you are looking for? Post a new question.