Search tips
Showing 35 results View by: Thread Post Sort by
    Answered

  • DRV8706S-Q1EVM: Support Required for DRV8706S-Q1 SPI Communication Issue

    Resolved
    Part Number: DRV8706S-Q1EVM Hello Team, I am currently working with TI’s DRV8706S-Q1 motor driver and encountering an issue while attempting to access its registers via an external MCU over SPI. When I try to write to the registers, the operation…
    • Resolved

  • DRV8706S-Q1EVM: When I use DRV8706S in 12V system, did I need to do something about Miller Clamp for motor driver?

    TI Thinks Resolved
    Part Number: DRV8706S-Q1EVM Other Parts Discussed in Thread: UCC23514 Dear all When I read the datasheet and circuit schematic diagram of DRV8706S and EVM, I did not find any pin of DRV8706S is for Miller Clamp, When I use DRV8706S in 48V system…

  • DRV8706S-Q1EVM: When I use DRV8706S in 48V system, did I need to do something about Miller Clamp for motor driver?

    TI Thinks Resolved
    Part Number: DRV8706S-Q1EVM Other Parts Discussed in Thread: UCC23514 Dear all When I read the datasheet and circuit schematic diagram of DRV8706S and EVM, I did not find any pin of DRV8706S is for Miller Clamp, When I use DRV8706S in 48V system…

  • LP-MSPM0L1306: Regarding LP-MSPM0L1306 and DRV8706S-Q1EVM

    Part Number: LP-MSPM0L1306 Other Parts Discussed in Thread: DRV8706S-Q1EVM , , SYSCONFIG , MSPM0L1306 Content from [Company-specific] IT Ticket: [Company] is prototyping a new power-stage architecture for EZ Drive ECU. The purpose of these activities…

  • LP-MSPM0L1306: Regarding LP-MSPM0L1306 with DRV8706S-Q1EVM

    Part Number: LP-MSPM0L1306 Other Parts Discussed in Thread: DRV8706S-Q1EVM Hello-- The purpose of this post is to attempt to streamline the bring-up for other users, given my extensive troubles. CCS Version: 20.5.0.28__1.11.0, Default VS Code API…
    • Answered

  • DRV8706S-Q1EVM: Did I need set resistor, capacitance, or R_pull_down between gate and drain between MOSFET?

    Resolved
    Part Number: DRV8706S-Q1EVM Dear all I tend to use DRV8706S in the design, could you be kind enough to help solve the following questions: (1)Did I need set resistor, capacitance, or R_pull_down between gate and drain between MOSFET? (2) In…
    • Resolved
    • Answered

  • DRV8706S-Q1EVM: Required the connector pin pitch

    Resolved
    Part Number: DRV8706S-Q1EVM Tool/software: I have a question about the marked sections. Could you please provide the connector pitch size and the screw terminal wire size
    • Resolved

  • DRV8706S-Q1EVM: Red Warning Lights on GUI upon connection to Laptop

    TI Thinks Resolved
    Part Number: DRV8706S-Q1EVM Other Parts Discussed in Thread: LP-MSPM0L1306 , DRV8706-Q1 Tool/software: I am following this guide to setup the EVM: Brushed Motor Control User Guide . However when I connect the EVM to my laptop using the GUI , the warning…
    • Answered

  • DRV8706S-Q1EVM: Clearing Latch

    Resolved
    Part Number: DRV8706S-Q1EVM Other Parts Discussed in Thread: DRV8706-Q1 , DRV8106-Q1 Tool/software: Hello team, Just want to make sure. For DRV8706-Q1 and DRV8106-Q1 SPI variant device, to clear the latch caused by the fault event, just sending the…
    • Resolved
    • Answered

  • DRV8706S-Q1EVM: About SPI SDO output voltage

    Resolved
    Part Number: DRV8706S-Q1EVM The data sheet below states that the minimum value of the SDO output voltage(Voh) for SPI communication is "0.8*DVDD@Idout=5mA", but is it correct to understand that as the current decreases, the voltage drop voltage decreases…
    • Resolved

Didn't find what you are looking for? Post a new question.