Search tips
Showing 35 results View by: Thread Post Sort by

  • DRV8836: DRV8836 OUT waveform issue

    TI Thinks Resolved
    Part Number: DRV8836 Other Parts Discussed in Thread: DRV8834 Tool/software: Hi TI : So far we are going to verify moto driving signal waveform. we found the wavefrom seems not square wave. when signal High level to Low level, The waveform will slow…

  • DRV8836: DRV8836 timing issue

    Part Number: DRV8836 Tool/software: Hi TI : we follow the datasheet and go to check timing about AINx to AOUTx or BINx to BOUTx. we found the timing seems different with datasheet. is it correctly ?? could you help to check test result ? have any impact…

  • DRV8836: DRV8836 Timing requirements

    Part Number: DRV8836 Tool/software: Hello Expert, The timing requirements is tested when Rl=20ohm. If the Rl=31ohm, how these values changed? Do we still need to follow the maxi value listed in the table? Best regards, wenting

  • DRV8836: questions of DRV8836

    Part Number: DRV8836 Dear Team, Here’s a design question about DRV8836, if our SOC I/O power rail is 1.8V, do we need to add level shift for control signal? As we know, the VIH should be 0.5Vcc, is there any risk for our design? Many Thanks, …

  • DRV8836: There is a problem driving 3.7V hollow cup motor with DRV8836DSSR (12 pin)

    TI Thinks Resolved
    Part Number: DRV8836 Other Parts Discussed in Thread: TMS320F28035 Hi Team, Requirement: using the DRV8836DSSR chip to drive the hollow cup motor, but now there are some problems as follows: The main control chip being used is TMS320F28035 (56 pin) chip…

  • RE: DRV8836: Multisim simulation model

    Hi Pablo Armet, Pablo Armet said: Which inverter are you referring to? Is the part in red the inverter? Pablo Armet said: What resistance you referring to? The resistors to configure the 555 timer to generate 100kHz freq at 50% duty cycle? Yes. Pablo Armet…
    • Answered

  • DRV8836: schematic review

    Resolved
    Part Number: DRV8836 Other Parts Discussed in Thread: DRV8428E Hi team, my customer wants to use motor driver on monitor XY movement application, would you help check if this is OK, especially the VCC ? thanks
    • Resolved

  • DRV8836: DRV8836 vs DRV8834 lower phase current / RDSon

    Part Number: DRV8836 Other Parts Discussed in Thread: DRV8834 , , DRV8834EVM Hi all Referring to this former post: https://e2e.ti.com/support/motor-drivers/f/motor-drivers-forum/977132/drv8836-parameters-affecting-rdson my customer has provided these additional…

  • DRV8836: Substitute inquiry (functionally)

    TI Thinks Resolved
    Part Number: DRV8836 Hi, TI Support Team Due to the delivery problem of DRV8836DSSR at the customer We are reviewing the DRV8428PRTER product. Can it be replaced in terms of functionality (drive)? Specifically, is it possible to operate the same for the…

  • DRV8836: The specifications are not very clear. If this drive is full, half, or can be classified into segments?

    TI Thinks Resolved
    Part Number: DRV8836 The specifications are not very clear. The customer would like to know if this drive is full step, half step, or can be classified into segments? Best Regards Cherry Zhou

Didn't find what you are looking for? Post a new question.