• DRV8912-Q1: SPI Settings for continuous mode operation in DRV8912

  

  reshma b

  TI Thinks Resolved

  Part Number: DRV8912-Q1 Tool/software: Hi, I am using DRV8912 in parallel configuration (4 half bridges connected parallelly) and planning to operate them in continuous mode. The configuration settings for Control register1 using SDI are 0x08AA and for…

  • 4 days ago
  • Motor drivers
  • Motor drivers forum

• DRV8912-Q1: Evaluation of DRV8912 Control Process

  

  Quang Bach Minh

  TI Thinks Resolved

  Part Number: DRV8912-Q1 Tool/software: Hi team, I am considering using the DRV8912 to control a relay. After reviewing the datasheet for the driver, I have outlined the control process and fault recovery in the diagram below. I would greatly appreciate…

  • 2 months ago
  • Motor drivers
  • Motor drivers forum

• DRV8912-Q1: When outputting a high impedance state, there is still a path between the output and ground

  

  Jacob

  TI Thinks Resolved

  Part Number: DRV8912-Q1 Other Parts Discussed in Thread: DRV8816 Tool/software: Hi, team I used DRV8912 as a 24V driver, but when the output is disabled, there seems to still be a path between the output pin and ground. Because when there was no load…

  • 17 days ago
  • Motor drivers
  • Motor drivers forum

• DRV8912-Q1: OLD detection

  

  Phan Dat

  Part Number: DRV8912-Q1 Tool/software: Dear Team, I am currently using the DRV8912 in continuous mode to control a relay , and I have a concern regarding the OLD detection mechanism . I have connected the HS OUT1 pin to the signal pin of the relay and…

  • 2 months ago
  • Motor drivers
  • Motor drivers forum

• DRV8912-Q1: Motor operation Table for chopping mode

  

  Josuar Priebe

  Part Number: DRV8912-Q1 Tool/software: Hello, in the Datasheet I found "Table 2. Motor Operation in Continuous Mode" and "Table 5. Motor Operation in Parallel Mode (Continuous Operation)" giving a nice overview of OUTx states depending on…

  • 2 months ago
  • Motor drivers
  • Motor drivers forum
Answered

• DRV8912-Q1: DRV8912-Q1

  

  Nihal Kumar

  Resolved

  Part Number: DRV8912-Q1 Other Parts Discussed in Thread: DRV8906-Q1 Tool/software: Hi Readers, I have a query, I need to select triple channel H-bridge driver(with SPI interface) for brushed motor, in which I need to connect two BDC motor making one h…

  • Resolved

  • 11 months ago
  • Motor drivers
  • Motor drivers forum

• DRV8912-Q1: Writing a register resets all other register.

  

  David Dudley

  Part Number: DRV8912-Q1 Tool/software: Seem to have the strangest problem... I'm using a DRV8912 interface through a MicroChip MCP2210 USB to SPI Interface chip. I've used this chip with a variety of components before, so this is not a new part…

  • 7 months ago
  • Motor drivers
  • Motor drivers forum

• DRV8912-Q1: Minimum Component Height

  

  Jason Cao

  Part Number: DRV8912-Q1 Tool/software: Hello, Within the datasheet for DRV8912QPWPRQ1, I am only seeing a maximum component height of 1.2mm, but not a minimum. What is the minimum component height?

  • 8 months ago
  • Motor drivers
  • Motor drivers forum
Answered

• DRV8912-Q1: What is the consequence if short all OUTx together

  

  Josh Wei

  Resolved

  Part Number: DRV8912-Q1 Tool/software: Hi experts, Could you please help to identify whether this is a trouble or not? Customer would like to short all output pin together when testing in their production line. Thanks! Josh

  • Resolved

  • 7 months ago
  • Motor drivers
  • Motor drivers forum

• DRV8912-Q1: Power Sequence

  

  Kyson Tan

  Part Number: DRV8912-Q1 Tool/software: Hi, Is there any power up and/or down sequence requirement for the Vm and Vdd rails of DRV8912? Thanks, Kyson

  • 10 months ago
  • Motor drivers
  • Motor drivers forum

Didn't find what you are looking for? Post a new question.