Search tips
Showing 19 results View by: Thread Post Sort by

  • DRV8962EVM: DRV8962EVM

    Part Number: DRV8962EVM Hello Murugavel, I am testing the DRV8962EVM board. connections details: 1.48V at VM and GND. 2. 3.3V power supply to EN1 and sleep Pin, 3.3V power to VCC and other pins Via USB of the board. 4. connected resistor load…

  • DRV8962EVM: DRV8962EVM

    Part Number: DRV8962EVM Hello Team, I have a question regarding connections for single solenoid & Gnd connections on EVM. 1. How to connect single solenoid to board.. I can see on positive connection on the board from the J14 pin1 and negative connection…
    • Answered

  • DRV8962EVM: Jumper configuration for DRV8962evm

    Resolved
    Part Number: DRV8962EVM Other Parts Discussed in Thread: DRV8962 Hello, In the Table A-1 of the Users' Guide, for the DRV89x2 variant, it shows J26 as DNP. But in the photograph of Figure A-4, DRV8962EVM jumper population guide, J26 is populated.…
    • Resolved

  • DRV8962EVM: drv8962evm

    TI Thinks Resolved
    Part Number: DRV8962EVM Hi I've connected a BDC motor as described in the GUI manual, can you please explain what is the meaning of low side / high side ? and what is the connection to J13 or J14 ? I've connected a BDC motor to J13 I've tried…

  • DRV8962EVM: Thermal issue

    Part Number: DRV8962EVM Other Parts Discussed in Thread: DRV8962 , DRV8962VEVM Tool/software: Hi Team, My customer is testing DRV8962, and meet some technical issue which need your support to solve as below. What is their expected spec esp. in thermal…

  • DRV8962EVM: DRV8962 TEC controller

    Part Number: DRV8962EVM Hi, team： I am using DRV8962EVM control single TEC, and short out1 to out2 ,out3 to out4, TEC connect between OUT1 to OUT3, and short IN1 to IN2, IN3 to IN4, use GUI contorl IN1 and IN3 input, but it doesn't work, could you help…

  • DRV8962EVM: 0.5 Volt Amplitude - 2.5 to 5 MHz noise in Current Reading Signals and PWM Signals

    Part Number: DRV8962EVM Hi, I am using DRV8962EVM in an application for Brushless DC linear motor control. A see a huge noise with 0.5 volt amplitude at 2.5-5 Mhz, only when turning on the power supply to the DRV8962EVM board. The noise appears…

  • DRV8962EVM: problems with the 4 current sense signals flattening out where there is non-zero current in stepper motor current control application

    TI Thinks Resolved
    Part Number: DRV8962EVM Other Parts Discussed in Thread: DRV8962 , DRV8845EVM , DRV8462 , DRV8962VEVM , DRV8262 Hi, We are trying to use DRV8962EVM and its 4 current sense signals as feedback signals in closing the current loop in a stepper motor control…

  • DRV8962EVM: What is the best way to calculate an overall current signal based on the 3 of the current readings (IPROPI 1 to 3) for evaluating equivalent overall current going through a 3-phase BLDC motor

    Part Number: DRV8962EVM Other Parts Discussed in Thread: DRV8962 , DRV8329 , DRV8312 , DRV8353 , DRV8350 Hi. We are implementing a control driver for 3-phase BLDC motors using DRV8962EVM. For the current monitoring features of the product, we need…

  • RE: DRV8962-Q1: Simulation model

    Hi Manoj, We do not have a model for simulating the functionality of the device. For testing configurations we recommend using the DRV8962EVM and its associated GUI. Regards, Joshua

Didn't find what you are looking for? Post a new question.