• DS160PR410: Design inquiries regarding the DS160PR410 redriver.

  

  evan hong

  Part Number: DS160PR410 Tool/software: Hi Sir, Due to layout requirements, I need to swap the differenrial pair's P and N lines. Is this permissible? BR, Evan Hong

  • 4 months ago
  • Interface
  • Interface forum

• DS160PR410: What to do with GAIN pin when DS160PR410 is used as I2C slave

  

  Karthikeyan S

  TI Thinks Resolved

  Part Number: DS160PR410 I am trying to configure DS160PR410 as an I2C slave should i connect the GAIN pin to ground or should i leave it floating.

  • 1 month ago
  • Interface
  • Interface forum

• DS160PR410: DS160PR410

  

  Kelley Kim

  TI Thinks Resolved

  Part Number: DS160PR410 Tool/software: Dear, Chip marking as below, What is the meaning of it? especially number (268, 248, 288...) PX410 TI 268 A73Z G4 PX410 TI 268 A73Z G4 PX410 TI 248 A0TQ G4 PX410 TI 288 A080 G4 PX410 TI 248 A0TQ G4…

  • 7 months ago
  • Interface
  • Interface forum

• DS160PR410-Q1: Automotive part DS160PR410-Q1 ESD Issue

  

  xiuting Huang

  Part Number: DS160PR410-Q1 Hi TI Experts: We encountered the DS160PR410-Q1 damage during the automotive electrostatic contact discharge (connector pin) ±4kV; Two ICs out of one ECU are all damaged. The impedance to GND of the TX pins (Pin1/2,…

  • 1 month ago
  • Interface
  • Interface forum

• DS160PR410-Q1: DS160PR410-Q1 Configuration Metohod Compatibility

  

  xiuting Huang

  TI Thinks Resolved

  Part Number: DS160PR410-Q1 HI TI experts: The DS160PR410-Q1 can be confitured with three different ways according to the datasheet, such as Pin mode, I2C controller mode (master), I2C target mode (slave). If we want to finally confiure DS160PR410…

  • 3 months ago
  • Interface
  • Interface forum

• DS160PR410: DS160PR410

  

  ying niu

  TI Thinks Resolved

  Part Number: DS160PR410 Tool/software: Hello, we are Hefei Kaimeng Technology, a company that makes mobile phone memory chips. We have designed a protocol analysis board, which uses DS160PR410 to adjust and compensate signals and capture and analyze UFS4…

  • 9 months ago
  • Interface
  • Interface forum

• DS160PR410: DS160PR410

  

  ying niu

  TI Thinks Resolved

  Part Number: DS160PR410 Tool/software: hi My company is Hefei kaimeng technology, making memory chips. At present, a grasping protocol analysis board is designed, DS160PR410 as the driver IC, to analyze the UFS4.0 protocol, so now the IBIS file of DS160PR410…

  • 9 months ago
  • Interface
  • Interface forum

• DS160PR410: SIGCON for DS160PR410

  

  Ramgopal Divakar

  TI Thinks Resolved

  Part Number: DS160PR410 Tool/software: Hello, I would like to use the SIGCON tool to create an EEPROM file or modify it for DS160PR410. Which version do I download from this tool below? For Linux and Windows. https://www.ti.com/tool/SIGCONARCHITECT…

  • 9 months ago
  • Interface
  • Interface forum

• DS160PR410: The recommended location for the DS160PR410 on the PCIE link

  

  Yuxi Liu(Tony)

  TI Thinks Resolved

  Part Number: DS160PR410 Tool/software: Hi TIer Where is the DS160PR410 recommended on the PCIE link? Are they near the transmitter, near the receiver, near the board connector end, or are they not explicitly required? Our current layout design…

  • 8 months ago
  • Interface
  • Interface forum
Answered

• DS160PR410: READ_EN_N termination

  

  Keith Krasnansky

  Resolved

  Part Number: DS160PR410 The datasheet says this pin should be pulled high for normal operation when EN_SMB = L3, but if this is an active low reset, shouldn't the signal be pulled low as power comes up so that the IC is in a known state at power up? Is…

  • Resolved

  • 1 month ago
  • Interface
  • Interface forum

Didn't find what you are looking for? Post a new question.