Answered

• DS90UB913A-CXEVM POC max Supply crrent

  

  Kikuo Mita

  Resolved

  Other Parts Discussed in Thread: DS90UB913A-CXEVM Please advise me using DS90UB193A-CXEVM Q1. DS90UB913A-CXEVM is used in POC mode, supplying 5V CD from DS90UB914A how much current does DS90UB913AEVK consume at most? Q2 How much current can POC supply…

  • Resolved

  • over 11 years ago
  • Interface
  • Interface forum

• [DS90UB913A-CXEVM & DS90UB914A-CXEVM] Gerber data for REV A board

  

  Chang-woo YANG

  Other Parts Discussed in Thread: DS90UB913A-CXEVM , DS90UB914A-CXEVM Hello~ If possible, would you please share the gerber data of DS90UB913A-CXEVM & DS90UB914A-CXEVM ?? Thanks... C.W. :)

  • over 12 years ago
  • Interface
  • Interface forum

• DS90UB913A-Q1: Recommended connectors and cables

  

  Shuji Ishiwata

  TI Thinks Resolved

  Part Number: DS90UB913A-Q1 Other Parts Discussed in Thread: DS90UB913A-CXEVM Hi All, Please let me know if you have any candidate/recommended connectors/cables when using the DS90UB913A-CXEVM. Best Regards, Ishiwata

  • over 1 year ago
  • Interface
  • Interface forum
Answered

• DS90UB913A-CXEVM configuration

  

  Joe Rule

  Resolved

  Hello, We have a DS90UB913A/914A EVM and we can get the setup to "lock" when no camera is connected but we see no data when probing the LVDS serial transmission lines between the 2 boards. We have it configured to use the SMA connector interfaces, not…

  • Resolved

  • over 11 years ago
  • Interface
  • Interface forum

• RE: DS90UB914A-CXEVM: FDP III Link - Single frames on-demand acquisition and storage

  

  Thomas Bejin

  Hi Alessio, For the UB914A EVM the video data is output via a parallel interface which can be seen below labeled as LVCMOS Outputs (video). This is from the DS90UB913A-CXEVM and DS90UB914A-CXEVM REV A User’s Guide (Rev. B) (ti.com) To store and…

  • over 1 year ago
  • Interface
  • Interface forum
Answered

• DS90UB913A/14A-CXEVM: I2C communication with Remote slave attached to Remote SER

  

  Christian Pelletier

  Resolved

  Hi, I want to communicate to a remote slave to Remote SER. MCU =­­> DES => SER => MCU I tried the following configuration : Local I2C MCU => DES I2C device ID = 0x60 I read 0xC0 at reg addr 0x00 (0x60<<1) Communication works fine. I…

  • Resolved

  • over 11 years ago
  • Interface
  • Interface forum
Answered

• DS90UB914A-CXEVM: Apply for EVM

  

  Kygo Cheng

  Resolved

  Part Number: DS90UB914A-CXEVM Other Parts Discussed in Thread: DS90UB913A-CXEVM , Hi Team, I need EVM to test Could I apply for DS90UB913A-CXEVM & DS90UB914A-CXEVM currently? THX

  • Resolved

  • over 4 years ago
  • Interface
  • Interface forum
Answered

• DS90UB913A-Q1: DS90UB913 and DS90UB914 DAP connection to GND- there are conflicting instructions in the datasheet

  

  Z78M12

  Resolved

  Part Number: DS90UB913A-Q1 Other Parts Discussed in Thread: DS90UB913A-CXEVM , DS90UB914A-CXEVM Hi, We about to end the layout this week and the layout person just highlight something regarding thermal pad connection, so we need your feedback ASAP. …

  • Resolved

  • over 4 years ago
  • Interface
  • Interface forum

• DS90UB914A-CXEVM: step files

  

  nadav aharon

  TI Thinks Resolved

  Part Number: DS90UB914A-CXEVM Other Parts Discussed in Thread: DS90UB913A-CXEVM hi , i'm building an adapter for both serializer and deserializer and i'm looking for the 3D files of both DS90UB914A-CXEVM & DS90UB913A-CXEVM boards any idea where…

  • over 5 years ago
  • Interface
  • Interface forum

• DS90UB936-Q1: FPD-Link III compliance testing and Ser EVM

  

  Connie Lu1

  TI Thinks Resolved

  Part Number: DS90UB936-Q1 Other Parts Discussed in Thread: DS90UB913A-CXEVM , DS90UB935-Q1 Hi team, As my customer is going to use DS90UB936-Q1, they are looking for the required test setup and test software to validate FPD-Link in 936 design. Can…

  • over 5 years ago
  • Interface
  • Interface forum

Didn't find what you are looking for? Post a new question.