Search tips
Showing 723 results View by: Thread Post Sort by
    Answered

  • RE: BQ34Z100-R2: Current Calibration Producing Incorrect Current Measurements

    Resolved
    Hi Steven, Thanks for the prompt reply. I understand your point from the first sentence, but I'm unsure how much difference that would be rather than using the wire terminal input connector TB3 (at least not in the DC current case I would imagine)…

  • RE: TPA3255: Fault stays low in PBTL configuration - RESET not working

    Hi Théo. About this case, could I confirm something with you. 1. Do you mean if you don't connect 10uF to INC and IND will cause Fault? like below figure. Théo Mnbs said: With this 'upgrade', TPA3255 is reacting normally. /FAULT & /CLIP are…

  • Asking for boost TPS61089 design suggestions

    Other Parts Discussed in Thread: TPS61089 , TAS2781 , TPS61288 , TPS61178 , TPS61376 Hi Team, Customer would like to design boost IC for audio amp. TAS2781’s EVM place TPS61089. However, the output 12V is not enough for customer’s requirement. …

  • RE: TAS5825PEVM: MCU

    Hi Jeff we don't have an independent mcu board for amp evm board. if customer want the USB2ANY device, below link should be able to get one. https://www.ti.com/tool/USB2ANY this device can also be used for connecting amp evm board. thanks. jesse
    • Answered

  • RE: TAS5825P: End System Integration Wiring method inqury

    Resolved
    Hi Jay if tas5822 can connect successfully, tas5825p should work too. how many amp devices been used on customer's board, for tas5825p evm board only assembled 1pcs amp device, so in-system tuning with over 1 amp might not work. BTW, do customer have…

  • RE: TLV320AIC3254: EQ related inquiries

    Hello MJ, I am not sure if I understand your questions correctly so please clarify if I misunderstood something. Q1. Is it possible to adjust EQ for each L/R ch? After checking the EVM User's guide, it is confirmed that the EQ function is adjusted in…
    • Answered

  • USB-C-PD-DUO-EVM: TPS65987D Issues with Programming

    Resolved
    Part Number: USB-C-PD-DUO-EVM Other Parts Discussed in Thread: TIDA-050012 , TPS65987D I have a custom PCB designed to utilize the reference design from the source side of the USB-C-PD-DUO-EVM. The sink side was not utilized. The PCB is designed to take…
    • Resolved

  • RE: EVM430-FR6043: EVM430-FR6043 for water flow with 1000 kHz transducers

    To start, I would say that you should probably be using FR6043EVM_USS_Water_Demo instead since there are hard frequency limits in the gas firmware if I remember correctly. For a 6043 in water mode to work with the GUI, you'll need to click Options…

  • DRV8353RS-EVM: Motor drivers forum

    TI Thinks Resolved
    Part Number: DRV8353RS-EVM Other Parts Discussed in Thread: DRV8353 , CSD19532KTT Hello Team, We are a startup company named DeccanR Enterprises Pvt Ltd., from India. We are working on Automotive Application of building an EV two-wheeler 60V BLDC Motor…

  • TRF371125EVM: baseband amplifier not working for the evaluation board

    TI Thinks Resolved
    Part Number: TRF371125EVM I followed the instruction for the EVM test in the datasheet. The current that the board runs is 290mA instead of 385mA in the datasheet. When I checked using a spectrum analyzer, the mixer itself worked, but the BB amp did not…

Didn't find what you are looking for? Post a new question.