• UCD90160A: Configuring Rail 2 Startup Behavior in Fusion Digital Power Designer

  

  Muvva Navin Krishna

  TI Thinks Resolved

  Part Number: UCD90160A Tool/software: Hi, I am using the UCD90160ARGCR as a power sequencer in my design and configuring it using Fusion Digital Power Designer . I have created 10 power rails with the required voltages and sequencing. However, I need help…

  • 16 days ago
  • Power management
  • Power management forum

• RE: TPSM831D31: How to build a project in Fusion Digital Power Designer?

  

  fs wang

  Hi Nick, Thanks for the answer, I'm also studying TPS53681 now, I will check if we should buy the eval board before we have prototype devices build.

  • 9 days ago
  • Power management
  • Power management forum

• UCD74111: Fusion Digital Power Designer

  

  Torsten Geist

  TI Thinks Resolved

  Part Number: UCD74111 Other Parts Discussed in Thread: UCD9222 , Tool/software: Hello, We use the Fusion digital power designer tool to program 2x core voltage regulators UCD74111 with the UCD9222 regulator. We used version 7.10.1 Under Monitor, where you…

  • 1 month ago
  • Power management
  • Power management forum
Answered

• RE: UCD3138A: Setup Fusion Digital Power Designer GUI software

  

  Hemanth Sreeperumbudur

  Resolved

  Hi Amath, Please try FUSION-DIGITAL-POWER-STUDIO Application software & framework | TI.com Fusion Digital Power Studio for UCD3138 Isolated Power Applications (Rev. C) Regards Hemanth

  • 4 months ago
  • Simulation, hardware & system design tools
  • Simulation, hardware & system design tools forum

• UCD3138: Can Fusion Digital Power Studio support BUCK topology for UCD3138?

  

  Jimmy WANG

  TI Thinks Resolved

  Part Number: UCD3138 Other Parts Discussed in Thread: TIDA-00653 , TIDA-00705 , PMP21529 , PMP20587 , PMP23332 , PMP4486 , Tool/software: Hi team, Can Fusion Digital Power Studio support BUCK topology for UCD3138? if not. How can fast design buck topology…

  • 9 months ago
  • Power management
  • Power management forum

• RE: TPS53679: Phases cannot be recognized by Fusion Digital Power Designer tool

  

  Maha Noor

  Hi Moon, The waveform looks fine except for some ringing on VSW, which may just be due to measurement noise. I was hoping you could send a waveform of PWM and CSP for each phase with the bad controllers to see if they are working. Also, please send your…

  • 4 months ago
  • Power management
  • Power management forum

• TPS53679: Device not detecting on Fusion Digital Power Designer

  

  kaikai sun

  TI Thinks Resolved

  Part Number: TPS53679 Tool/software: We connected ASKIP pin to En/FCCM of power stage with 0Ohm and also the signal was pulled up to 5V with 2.21Ohm resistor。Why?

  • 5 months ago
  • Power management
  • Power management forum

• UCD3138CC64EVM-030: Fusion Digital Power Studio iout isfault in the tab Monitor (DC-DC-LLC UCD3138)

  

  Tasmiya

  TI Thinks Resolved

  Part Number: UCD3138CC64EVM-030 Other Parts Discussed in Thread: UCD3138 Hello, I am receiving a fault message in the "Output Current" column of the Status Registers/lines. How can I correct this?

  • 11 months ago
  • Data converters
  • Data converters forum

• UCD3138: UCD3138,TI-Fusion-Digital-Power-Studio,USB-TO-GPIO2 (2022)

  

  zhouyu zhou

  TI Thinks Resolved

  Part Number: UCD3138 Other Parts Discussed in Thread: USB-TO-GPIO2 we used USB-TO-GPIO (2006) adapter to monitor UCD3138's digital power, but now we buy a new adapter USB-TO-GPIO (2022) ,we use the software TI-Fusion-Digital-Power-Studio-3.0.42 , the…

  • over 1 year ago
  • Power management
  • Power management forum
Answered

• RE: TPSM846C23: fusion digital power designer online mode not working

  

  Mahalakshmi C

  Resolved

  Hi Peter, We had some restriction in old PC. We tried in different system and it worked. Also we added pullups as you have mentioned. Thanks

  • 7 months ago
  • Power management
  • Power management forum

Didn't find what you are looking for? Post a new question.