Search tips
Showing 8,207 results View by: Thread Post Sort by

  • RE: UCD3138064: FUSION-PRODUCTION-GUI

    Hello Rex, Here are a few notes that I have noticed: Checksums Listed Based on your E2E posts, the following are the various checksums that you have either calculated, or are being calculated by the Fusion Production GUI. Desired Checksum: 0x02000…

  • UCD90320U: Fusion GUI error

    TI Thinks Resolved
    Part Number: UCD90320U Tool/software: Dear TI Team, I have a Fatal Error when I try to configure a GPI as a condition of Re-Sequence. I also have the error when the GPI is configured as FAULT. Fullscreen LOG_Fusion_error_GPI.txt Download…

  • FUSION_DIGITAL_POWER_DESIGNER: Fusion Digital Power Designer GUI User Guide

    TI Thinks Resolved
    Part Number: FUSION_DIGITAL_POWER_DESIGNER Tool/software: Good day, Can you please confirm the latest version of Fusion Digital Power Designer GUI 7.0 for the UCD90xxx Sequencer (SLVUB51)? We are using the May 2017 issue and it references v7.0.11…

  • USB2GPIO-LOADER-SW: Command based GUI in Fusion similar to older version

    TI Thinks Resolved
    Part Number: USB2GPIO-LOADER-SW Other Parts Discussed in Thread: USB-TO-GPIO2 Tool/software: Hi, I wish to send the command read/write with my own data to VCU118 device (which has SMBus protocol implemented) using Fusion GUI through USB-to-GPIO2 device…
    • Answered

  • UCD90120A: Typo in Fusion Digital Power Designer GUI?

    Resolved
    Part Number: UCD90120A Tool/software: Hello, I am using the Fusion Digital Power Designer (in offline mode) to create a configuration file for the UCD90120A. Section 7.4.11 of the UCD90120A datasheet gives this info on GPI Special Functions: But when…
    • Resolved

  • TPS536C7EVM-051: I would like to monitor all 12 phase output voltage waveforms of TPS536C7 in Fusion GUI.

    TI Thinks Resolved
    Part Number: TPS536C7EVM-051 Other Parts Discussed in Thread: TPS536C7 Tool/software: I want to monitor all 12 phase output voltage waveforms of TPS536C7 in Fusion GUI, but when I try to change the Advanced settings in RAIL Configuration, the PASSWORD…
    • Answered

  • UCD9090-Q1: ENABLE_ACTIVE_TRIM using Fusion GUI

    Resolved
    Part Number: UCD9090-Q1 Tool/software: Please show how to activate ENABLE_ACTIVE_TRIM using Fusion GUI, I can't find it in GUI. I would like to use it to adjust the output through VOUT_COMMAND.
    • Resolved
    • Answered

  • UCD3138A: Setup Fusion Digital Power Designer GUI software

    Resolved
    Part Number: UCD3138A Other Parts Discussed in Thread: UCD3138 Tool/software: Hello, I was installing the Fusion Digital Power Designer GUI software, but following the guide I can't find UCD3xxx Device GUI, there is only UCD9xxx Device GUI. But my need…
    • Resolved

  • UCD90160A: Fusion Gui problem

    TI Thinks Resolved
    Part Number: UCD90160A Tool/software: Hi team, What's the meaning of Vout Exponent/Vout Scale Mon/Vout Cal Mon? Could you please explain in detail?

  • DLPDLCR160CPEVM: EVM DMD device ID does not match GUI product ID

    TI Thinks Resolved
    Part Number: DLPDLCR160CPEVM Tool/software: Hello E2E Experts, Good day. DLP-EVM-GUI-4.0.0.15-Setup.exe: Hardware connection: My question is whether the development board model DLPDLCR160CPEVM corresponds to the GUI. If not, please send the…

Didn't find what you are looking for? Post a new question.