• ISO1211: Output state of ISO1211 in case of breakdown

  

  user1376079

  TI Thinks Resolved

  Part Number: ISO1211 Hello Team, What would output from ISO1211, if RTHR is shorted and lead to a large input current and eventual device damage? (High/ Low/ Hi-Z) We are thinking of using ISO1211 to input DC110V. Regards, Taiki Koga

  • 3 months ago
  • Isolation
  • Isolation forum

• ISO1211: Where can I get the model of the ISO1211 for TINA Tool?

  

  Vladimir Villamizar

  TI Thinks Resolved

  Part Number: ISO1211 Other Parts Discussed in Thread: TINA-TI , TVS3300 Hello. I am simulating a digital input model with TINA Tool, with de IC ISO1211, I can't found the ISO1211 model, there is a ISO121x Model, but the pins are very diferent from the…

  • 4 months ago
  • Isolation
  • Isolation forum

• ISO1211: apply the 24v/500khz

  

  Chen Alex1

  TI Thinks Resolved

  Part Number: ISO1211 Other Parts Discussed in Thread: ISO1212 HI sir could ISO1212 apply the 24v/500khz squre waveform ? thanks

  • 2 months ago
  • Isolation
  • Isolation forum

• RE: ISO1211: ISO1211 AC detection

  

  Rick Liu

  Hi Koteshwar Rao , Thank you for your kind support, Actually,We use ISO1211 for AC 220V detect function in our product design , and we refer circuit as below : Q1 : If we want the ISO1211 output is stable DC voltage level , could I adjust Cin cap value ? …

  • 5 months ago
  • Isolation
  • Isolation forum

• ISO1211: replacement device

  

  cafain

  TI Thinks Resolved

  Part Number: ISO1211 Other Parts Discussed in Thread: ISOM8710 HI Staff I'm thinking of replacing the TLP187(TOSHIBA) with a TI product. Do you have any devices you can suggest? dest regards cafain

  • 3 months ago
  • Isolation
  • Isolation forum
Answered

• ISO1211: Output Pull-down Resistor

  

  PY (Pengyu) Song

  Resolved

  Part Number: ISO1211 Hi team, Per below table in datasheet, it seems ISO1211 can drive up to 1kohm output resistance. Can put 100kohm resistor at output as pull-down resistor? Thanks.

  • Resolved

  • 4 months ago
  • Isolation
  • Isolation forum
Answered

• ISO1211: SUB Pin Connection

  

  PY (Pengyu) Song

  Resolved

  Part Number: ISO1211 Hi team, Understand from datasheet that SUB pin should be floating and not to connect to FGND or any other signal. Can you please share what is the reason of floating the SUB pin? Since it is chip substrate, it would be already at…

  • Resolved

  • 5 months ago
  • Isolation
  • Isolation forum
Answered

• ISO1211: Output current rating

  

  Kazuki Itoh

  Resolved

  Part Number: ISO1211 Hi team, Could you let me know how to interpret output current rating IOH of ISO1211? When VCC=3.3V, IOH min. is specified as -3mA. Does it specify the maximum sink current allowed? I don't get why sink current is specified for…

  • Resolved

  • 7 months ago
  • Isolation
  • Isolation forum
Answered

• ISO1211: Isolated Digital I/O

  

  d_zero

  Resolved

  Part Number: ISO1211 Other Parts Discussed in Thread: TIDA-00319 , TIDA-00236 , TIDA-00320 Dear *, TI has isolated digital inputs ISO1211. Does TI also has an isolated digital output IC? If no do you have a recommended way how to design isolated digital…

  • Resolved

  • over 1 year ago
  • Isolation
  • Isolation forum
Answered

• ISO1211: ISO1211 question check

  

  Bo Xian Yeh

  Resolved

  Part Number: ISO1211 Hi Team, My customer has question about ISO1211 formula. Below is IEC 61131-2 type-1 standard. For type 1, the turning point is 15V between VIH and VIL. If use our below formula, VIH is not equal to VIL. If customer want to use 15V…

  • Resolved

  • over 1 year ago
  • Isolation
  • Isolation forum

Didn't find what you are looking for? Post a new question.