• ISO1432: RS422-RS232

  

  Aidan Hamm

  Part Number: ISO1432 This module appears to be able to work between RS232-RS422. Is this correct? Since one side is a differential (RS422) and the other is not (RS232). Can someone please confirm, or point to where a part like this is available?

  • 22 hours ago
  • Isolation
  • Isolation forum

• ISO1432: Performance Parameters of ISO1432BDW

  

  Hardware Intern

  Part Number: ISO1432 I am designing a system using the ISO1432BDW transceiver operating at a data rate at 1 Mbps .To ensure strict adherence to our design margins, could your technical applications team provide guidance on the following operational specifications…

  • 22 days ago
  • Isolation
  • Isolation forum

• ISO1432: bsolescence report for the components

  

  Hardware Intern

  TI Thinks Resolved

  Part Number: ISO1432 Could you please provide an obsolescence report for the components listed below? We are seeking long-term availability for a minimum of 10 years. For our internal tracking, we categorize obsolescence into the following four groups…

  • 2 months ago
  • Isolation
  • Isolation forum

• ISO1432: "Clock Signal support on the ISO1432DWR chip"

  

  Sampat Kumar

  TI Thinks Resolved

  Part Number: ISO1432 Hi Team, We are currently planning to using the ISO1432DWR device for interfacing SDLC (Synchronous Data Link Control) signals. On the Single Ended side, we have the following single-ended signals: TX_Data RX_Data TX_CLK …

  • 3 months ago
  • Isolation
  • Isolation forum

• ISO1432: Recommended series resistor

  

  ArTzy

  TI Thinks Resolved

  Part Number: ISO1432 Hi Experts, For ISO1432BDW, can you please recommend series resistor on RS422 lines for max 921600 baud rate? Thank you. Regards, Archie A.

  • 9 months ago
  • Isolation
  • Isolation forum

• ISO1432: maximum admissable diode capacitance and Current drawn ICC2 for 115200 bps and 921600 bps baud rates

  

  Lokesh prasad Ganta

  TI Thinks Resolved

  Part Number: ISO1432 I am using ISO1432BDW in my design. logic side is powered with same 3.3V which is powering the microcontroller (3.3V_D with respect to GND_D). bus side is powered with isolated 5V (5V_ISO with respect to GND_ISO). 47 ohm series resistance…

  • 20 days ago
  • Isolation
  • Isolation forum
Answered

• ISO1432: ESD (HBM) Voltage Ratings

  

  Siby VV

  Resolved

  Part Number: ISO1432 Other Parts Discussed in Thread: ISO1430 , ISO1412 , , ISO1410 Please provide the ESD (HBM) Voltage Rating for the ISO1410, ISO1412, ISO1430, ISO1432, ISO14350, ISO14352 and also the B versions of these part numbers. The datasheet…

  • Resolved

  • 8 months ago
  • Isolation
  • Isolation forum

• ISO1432: RS422 data over long cables | Termination

  

  BOOM

  TI Thinks Resolved

  Part Number: ISO1432 Tool/software: Monitoring data on RS422 for longer cable lengths Till 10 metres of length, RS422 works fine with and without termination till 921600 baud rate With ISO3086DWR for 100 metres cable, with termination of 100 ohm, data…

  • over 1 year ago
  • Isolation
  • Isolation forum

• ISOW1412: Communication with ISOW1412 -> ISO1432

  

  G Cant

  TI Thinks Resolved

  Part Number: ISOW1412 Other Parts Discussed in Thread: ISO1432 , Tool/software: Hello, I checked both ISO1432 and ISOW1412. Both seems to meet my specifications but I really liked that the ISOW1412 has the isolated DCDC built-in. I want to send…

  • over 1 year ago
  • Isolation
  • Isolation forum
Answered

• ISO1432: Half duplex and Full Duplex Modes

  

  TEMC

  Resolved

  Part Number: ISO1432 Tool/software: Can we use ISO1432B IC for both full duplex and half duplex . for half duplex mode can we short A ,Y and B ,Z externally with zero ohms.

  • Resolved

  • over 1 year ago
  • Isolation
  • Isolation forum

Didn't find what you are looking for? Post a new question.