• 

  Mattia Berton2

  • 13 days ago
  • Isolation
  • Isolation forum

  ISO6741: Reinforced isolation

  • Resolved

  Part Number: ISO6741 Hello, I see in the datasheet that this part is rated UL for single isolation
• 

  Oba

  • 3 months ago
  • Isolation
  • Isolation forum

  ISO6741: Safety-Related Certifications plan

  • Resolved

  Part Number: ISO6741 Hello, According to the datasheet, all safety-related certifications
• 

  Oba

  • 3 months ago
  • Isolation
  • Isolation forum

  ISO6741: VCC1/2 range

  • Resolved

  Part Number: ISO6741 Hello, I have a question for VCC1/2 range of ISO6741 . According
• 

  Kengo.Y

  • 13 days ago
  • Isolation
  • Isolation forum

  ISO6742: RTM schedule.

  TI Thinks Resolved

  Part Number: ISO6742 Hi team, Could you tell me RTM schedule for ISO6742? Since the ISO6741 of the same series has been released, is this coming soon? Sincerely. Kengo.
• 

  Koteshwar Rao

  • 14 days ago
  • Isolation
  • Isolation forum

  RE: ISO1432: ISO1432 for isolated SPI interface

  Hi Krunal, I would also like to add that if the two SPI nodes that you are trying to interface are on the same board or are on two different boards that are very close by, then you can use a digital isolator like ISO6741 to isolate SPI interface. If...
• 

  Koteshwar Rao

  • 1 month ago
  • Isolation
  • Isolation forum

  RE: ISO7742: Looking for isolation devices

  Hi Wen Li, Thanks for reaching out, please see my inputs below. Thanks. For your requirement of isolating UART signals of 1Mbps and a digital sync signal of 1MHz, you can use ISO6741. If you mean to say that the other PCB is powered by a different...
• 

  Joel Holland

  • 19 days ago
  • Data converters
  • Data converters forum

  RE: AMC1306E25: Bandwidth and max input voltage of isolated modulator

  Hi Tom, Would a capacitive isolator like this work well? Thanks, Joel
• 

  Dushmantha Rajapaksha

  • 2 months ago
  • Isolation
  • Isolation forum

  RE: ISO1042: CAN bus wake up with isolated CAN transceiver

  Hi Anand: Thanks for posting your question on E2E. Unfortunately, TI doesn't have a single chip solution for isolated CAN transceiver with CAN bus WAKE functionality. For a cost efficient two chip solution, you may consider our latest general...
• 

  Koteshwar Rao

  • 4 months ago
  • Isolation
  • Isolation forum

  [FAQ] ISOW7841: Can I connect VISO outputs of two or more ISOW7841 devices directly in parallel to get higher output current than the current supported by a single device (130mA)?

  • Resolved

  Part Number: ISOW7841 Can I connect VISO outputs of two or more ISOW7841 devices directly in parallel to get higher output current than the current supported by a single device (130mA)?
• 

  Koteshwar Rao

  • 3 months ago
  • Isolation
  • Isolation forum

  RE: ISO7041DBQEVM: I am using two ISO7841, but I want to substitute one of those for a ISO7041.

  Hi Gustavo, Thanks for doing an experiment with MISO line connected to ISOW7841 and confirming. Yes, MISO is the line that sees the most return propagation delay and it does point out that the main cause for issue is the higher propagation delay of...

Didn't find what you are looking for? Post a new question.

• Ask a new question