• RE: ISO6763-Q1: Difference between ISO7763 and 6763

  

  Aaditya Vittal

  Hi Kavin, Thanks for the schematic. Please see my markup below: As you can see in the boxed section, the INC and OUTD pins are connected together. Even if a diode is used, this does not mean that the digital isolator can be used for bidirectional communication…

  • 1 month ago
  • Isolation
  • Isolation forum
Answered

• ISO7763: Looking for a different Iso

  

  Nate Newman

  Resolved

  Part Number: ISO7763 Tool/software: Hi team, I'm making a reference design for an I/O module. Right now I have two ISO7763Ds sending SPI signals out to a high side switch and a stepper motor driver. I'd like to replace these with a single digital isolator…

  • Resolved

  • 5 months ago
  • Isolation
  • Isolation forum
Answered

• ISO7763-Q1: Reg: Need of old datasheet

  

  Manikandan L

  Resolved

  Part Number: ISO7763-Q1 Tool/software: Hi Team, Can you please provide old revision datasheet of SLLSEU7C revision. We need for the comparison purpose. So kindly check and provide the respective mentioned datasheet.

  • Resolved

  • 5 months ago
  • Isolation
  • Isolation forum

• ISO7763-Q1: Power Dissipation

  

  Saraswathy G

  TI Thinks Resolved

  Part Number: ISO7763-Q1 Other Parts Discussed in Thread: ISO7763 , How to compute the power dissipation of ISO7763 ?

  • 9 months ago
  • Isolation
  • Isolation forum

• ISO7763-Q1: Terminal resistors

  

  Saraswathy G

  TI Thinks Resolved

  Part Number: ISO7763-Q1 Is it needed to provide external terminal or current limiting resistors for each channel of this IC ? The block diagram already shows internal resistors of close to 1k. If yes, how to select the value of the resistors?

  • 9 months ago
  • Isolation
  • Isolation forum
Answered

• ISO7763-Q1: Different Voltage Level for VCC1 and VCC2

  

  Giovanni Principato

  Resolved

  Part Number: ISO7763-Q1 Hi, can i use different voltage level for VCC1 and VCC2 (e.g. 5V for VCC1 and 3.3V for VCC2)? Thanks in advance.

  • Resolved

  • 8 months ago
  • Isolation
  • Isolation forum

• ISO7763-Q1: Finding the number of transistors used in the IC

  

  Amit kumar

  TI Thinks Resolved

  Part Number: ISO7763-Q1 I am Hardware Safety engineer working on reliability work for powertrain application. I am working on software" Ansys medini" where we can calculate the fit rate of any active and passive component as per our environment. Therefore…

  • 11 months ago
  • Isolation
  • Isolation forum

• ISO7763: ISO7763 Reduce Propagation Delay Time

  

  Blindu Marcel

  TI Thinks Resolved

  Part Number: ISO7763 Other Parts Discussed in Thread: ISO7631FM , ISO7640FM , ISO7641FM Hi all, We design system with 4 ADC AD7768-1 and with the ISO7763 digital isolator for SPI. And we have realized that with 15MHz SPI frequency the microcontroller…

  • over 1 year ago
  • Isolation
  • Isolation forum
Answered

• ISO7763: Recommended operating conditions of VIH & VIL

  

  Koshi Ninomiya

  Resolved

  Part Number: ISO7763 Dear Team, My customer evaluates the ISO7763DBQR on their board, and when they measure the input vottage waveform, it is wider than the recommended operating conditions. VCCI=3.3V Recommended operating conditions: Absolute maximum…

  • Resolved

  • over 1 year ago
  • Isolation
  • Isolation forum

• ISO7763: alternative ADuM152

  

  GARETH OU

  TI Thinks Resolved

  Part Number: ISO7763 Hi Please suggest alternative ADuM152N0BRZ product , p2p is better

  • over 1 year ago
  • Isolation
  • Isolation forum

Didn't find what you are looking for? Post a new question.