Answered

• ISOM8610: Difference between datasheet and ISOM8610.OLB

  

  Hiroyasu Koike

  Resolved

  Part Number: ISOM8610 Tool/software: I downloaded ISOM8610.OLB and sample design. And I opened the file in PSPICE. Then, I found the pin assign was different between datasheet and ISOM8610.OLB. I believe datasheet is correct. Am I right?

  • Resolved

  • 8 months ago
  • Isolation
  • Isolation forum
Answered

• ISOM8610: Review of ISOM8610 SSR-Based Motor Control Circuit

  

  Sameep Pai S

  Resolved

  Part Number: ISOM8610 Tool/software: Dear Team, Greetings! We are planning to use the ISOM8610 solid-state relay (SSR) to isolate the microcontroller outputs from the high-voltage DC (HVDC) side in our custom motor control board. The target load is…

  • Resolved

  • 7 months ago
  • Isolation
  • Isolation forum
Answered

• ISOM8610: Design Questions

  

  Jacob Bolduc

  Resolved

  Part Number: ISOM8610 Tool/software: We are thinking of using for a design but a few questions. We want to make sure that there is no Opto-charictoristis in the part meaning no LED at all. Also is this part radiation hardened as this is a priority…

  • Resolved

  • 11 months ago
  • Isolation
  • Isolation forum

• ISOM8610: SPICE or TINA-TI Model Inquiry

  

  Shadman Ahmed

  TI Thinks Resolved

  Part Number: ISOM8610 Other Parts Discussed in Thread: TINA-TI Tool/software: Is there an working SPICE model or a TINA-TI model available for use for the ISOM8610 yet?

  • over 1 year ago
  • Isolation
  • Isolation forum

• ISOM8610: PRODUCTION STATUS

  

  Keith Kuemmerle

  TI Thinks Resolved

  Part Number: ISOM8610 Is there a estimate available for when the ISOM8610 will transition to production status? ISOM8610

  • over 1 year ago
  • Isolation
  • Isolation forum

• ISOM8610DFGEVM: CAD Model

  

  Elyssa Kaplan

  TI Thinks Resolved

  Part Number: ISOM8610DFGEVM Other Parts Discussed in Thread: ISOM8610 Tool/software: Do you have a CAD model of the ISOM8610 Evaluation Module? If not, can you share a mechanical drawing that shows mounting holes?

  • 7 months ago
  • Isolation
  • Isolation forum

• ISO1042: Ring CAN FD Network

  

  Francis Jiang

  TI Thinks Resolved

  Part Number: ISO1042 Other Parts Discussed in Thread: ISOM8610 Hi Team, Customer uses ISO1042 to design a ring CAN FD network with 4 modules. How should the terminating resistor be configured? 120/120/120/120? Or is it impossible to configure an effective…

  • 2 months ago
  • Isolation
  • Isolation forum

• ISO7810: Solution for High -speed I/O channels

  

  Marvn Arcangel

  Part Number: ISO7810 Other Parts Discussed in Thread: ISOM8610 Hi Experts, I need to have high speed I/O channels (min 1Mbps to max 10Mbps) that individually can be used as inputs or outputs. Each channel when used as output should source up to 300mA…

  • 1 month ago
  • Isolation
  • Isolation forum

• ISOM8711: Opto-Emulator - "Normally switch"

  

  Ohad Bonneh

  TI Thinks Resolved

  Part Number: ISOM8711 Other Parts Discussed in Thread: ISOM8110 , ISOM8610 , Tool/software: Hi Team, I'm looking for an isolation device that will replace a relay, The opto - emulators can be a good fit here, however, we want to be able to make…

  • 9 months ago
  • Isolation
  • Isolation forum

• ISO1211: broken wire detection

  

  Isee

  TI Thinks Resolved

  Part Number: ISO1211 Other Parts Discussed in Thread: ISOM8610 , ISO1228 , Tool/software: hi Team, Do you have dokumentation on the "broken wire detection" capability? Requirement is that diagnostics only has to be implemented with hardware. Regards…

  • 9 months ago
  • Isolation
  • Isolation forum

Didn't find what you are looking for? Post a new question.