TI E2E support forums
TI E2E support forums
  • User
  • Site
  • Search
  • User
  • E2E™ design support >
  • Forums
    • Amplifiers
    • API solutions
    • Audio
    • Clock & timing
    • Data converters
    • DLP® products
    • Interface
    • Isolation
    • Logic
    • Microcontrollers
    • Motor drivers
    • Power management
    • Processors
    • RF & microwave
    • Sensors
    • Site support
    • Switches & multiplexers
    • Tools
    • Wireless connectivity
    • Archived forums
    • Archived groups
  • Technical articles
  • TI training
    • Tech days
    • Online training
    • Live events
    • Power Supply Design Seminar
  • Getting started
  • 简体中文
  • More
  • Cancel


Search tips
Showing 9 results View by: Thread Post Sort by
  • IWRL6432: CW mode for testing

    Akihiko Fujinaka
    Akihiko Fujinaka
    TI Thinks Resolved
    Part Number: IWRL6432 Tool/software: Hello expert, For getting the CW mode on IWRL6432AOP, I found the following topic in e2e. e2e.ti.com/search Then found the following setting. Do we need any other setting than "FrameTrigMode" = "4 - CW…
    • over 1 year ago
    • Sensors
    • Sensors forum
  • IWRL6432: Is TX 2 CW mode supported?

    Yohennas Folly
    Yohennas Folly
    TI Thinks Resolved
    Part Number: IWRL6432 Hi, I wanted to check whether there is support for CW mode on TX 2 with MMWAVE_L_SDK_05_02_00_02? I know that CW mode isn't supported in the demo SDK currently, but we have changed the code to get that working and it works without…
    • over 2 years ago
    • Sensors
    • Sensors forum
  • Answered
  • IWRL6432: How can I activate CW mode for testing?

    Hung-Hsuan Lin
    Hung-Hsuan Lin
    Resolved
    Part Number: IWRL6432 Dear all, I just want to use CW mode for checking RF ACTIVE performance of our radar module More precisely I want generate a plot as below. How can I do this?
    • Resolved
    • over 2 years ago
    • Sensors
    • Sensors forum
  • IWRL6432AOP: How to enter CW mode?

    Daniel Cheng1
    Daniel Cheng1
    TI Thinks Resolved
    Part Number: IWRL6432AOP Other Parts Discussed in Thread: MMWAVE-L-SDK , IWRL6432 , , IWRL6432BOOST Tool/software: Hi Expert, I can't find related API in mmWave-L-SDK to enter CW mode, but I do find a define "CONTINUOS_WAVE_MODE_ENABE" which will…
    • 10 months ago
    • Sensors
    • Sensors forum
  • Answered
  • IWRL6432: Software(firmware or parameter) for performance verification of TX / RX Ant

    Dakeun Yun
    Dakeun Yun
    Resolved
    Part Number: IWRL6432 Tool/software: Hello. We are using IWRL6432. Our radar module has SPI port for sending ADC data and does not have interface for DCA1000. We are trying to verify the performance of ANT.(We would like to individually verify the…
    • Resolved
    • 2 months ago
    • Sensors
    • Sensors forum
  • RE: IWRL6432: IWRL6432Boost + DCA1000

    Pedrhom Nafisi
    Pedrhom Nafisi
    Hello, My own computer is Windows 11 and works fine, nor does mmWaveStudio crash after every post proc. Remind me, you guys are just looking for raw data collection correct? Nothing too custom nor anything that pushes the device past its intended…
    • over 1 year ago
    • Sensors
    • Sensors forum
  • RE: IWRL6432: Measuring OSC_CLK_OUT and MCU_CLK_OUT

    Alan Sutherland
    Alan Sutherland
    Hi Santosh, Having looked at this forum post , we found that by setting the registry value as stated (repeated below for convenience) enabled the 40MHz clock signal to be output and subsequently measured. volatile uint32_t * ANA_CFG_CLK_CTRL_REG1_CLKTOP…
    • over 1 year ago
    • Sensors
    • Sensors forum
  • RE: AWRL6432: How to use CW mode

    Tim Henderson
    Tim Henderson
    Hi, For testing purposes, You will have to use mmWave Studio CLI and follow the instructions in the post mentioned above: https://e2e.ti.com/support/sensors-group/sensors/f/sensors-forum/1235546/iwrl6432-how-can-i-activate-cw-mode-for-testing Regards…
    • over 2 years ago
    • Sensors
    • Sensors forum
  • Answered
  • [FAQ] DCA1000EVM: Support, Tools, Debugging, And More

    Pedrhom Nafisi
    Pedrhom Nafisi
    Resolved
    Part Number: DCA1000EVM Tool/software: The DCA1000EVM is an evaluation module (EVM) that is used to supplement a mmWave Sensor in order to capture raw ADC data. This post will cover everything and anything you need to know about the DCA1000, how to…
    • Resolved
    • 10 months ago
    • Sensors
    • Sensors forum

Didn't find what you are looking for? Post a new question.

  • Ask a new question