Search tips
Showing 218 results View by: Thread Post Sort by

  • LAUNCHXL CC13-90 EU Antenna Issue

    Other Parts Discussed in Thread: TEST Hello , We’ve bought a LAUNCHXL CC13-90 EU Rev 1.2.0 & FW Rev 1.0 We uploaded the firmware Serial_CC13xx_Collector_T2.hex on the launchpad . We have done several test using this launchpad , and it work well…
    • Answered

  • LAUNCHXL-CC13-90: Possible/how to adjust the delay between turning on PA and start of transmission in TI-15.4 example code?

    Resolved
    Part Number: LAUNCHXL-CC13-90 Other Parts Discussed in Thread: CC1310 , CC1190 Hi, I tried to find in the collector/sensor node example code, where to adjust the delay between setting PA pin high and start to transmission, but so far I couldn't find anything…
    • Resolved

  • LAUNCHXL-CC13-90: Range

    TI Thinks Resolved
    Part Number: LAUNCHXL-CC13-90 Hi, Good Day. I have a customer who is working with LAUNCHXL-CC13-90. Please see below his query for your reference. Thank you very much. I have gotten my hands on two of the devices to set up communication between one being…

  • LAUNCHXL-CC13-90: Antenna for LAUNCHXL-CC13-90

    Part Number: LAUNCHXL-CC13-90 Hello,Is there a Texas Instruments recommended External Antenna for Sub-1GHz LAUNCHXL-CC13-90 module?

  • LAUNCHXL-CC13-90: Range extender

    Part Number: LAUNCHXL-CC13-90 Hello, currently I am using LaunchXL-CC13-90 for small data transmission .Its giving a range of about 850m, is there a way to increase the range? I want a range upto 2 Km.
    • Answered

  • LAUNCHXL-CC13-90: Error uploading program

    Resolved
    Part Number: LAUNCHXL-CC13-90 While working on Project0 of CC13-90 I encountered a problem,the error tells "Error configuring Debug server:Error=operation was aborted". How to solve this problem?
    • Resolved
    • Answered

  • LAUNCHXL-CC13-90: Board not getting detected

    Resolved
    Part Number: LAUNCHXL-CC13-90 After unboxing CC1390 Launch-XL boards,I plugged boards into my laptop individually seems only one board is getting detected in my PC.The other board is not getting detected neither the Green LED is working.Can anyone help…
    • Resolved
    • Answered

  • LAUNCHXL-CC13-90: rfPacketErrorRate Example - Set to 27dBm

    Resolved
    Part Number: LAUNCHXL-CC13-90 Other Parts Discussed in Thread: CC1190 , TEST We are testing the indoor range of two CC13-90 boards with the rfPacketErrorRate Example. The example seems to run with 25 dBm on Rx and Tx. I only see 26dBm option in the table…
    • Resolved
    • Answered

  • LAUNCHXL-CC13-90: What happens to power consumption and TX/RX signal strength if RANGE_EXT_MODE is not used?

    Resolved
    Part Number: LAUNCHXL-CC13-90 Other Parts Discussed in Thread: CC1310 , CC1190 Hi, I am exploring the possibility to use a customized board based on CC1310 + CC1390 as a CC1310 standalone board. What will happen in terms of TX/RX signal strength and power…
    • Resolved

  • LAUNCHXL-CC13-90: What will cause failure of launchpad board?

    Part Number: LAUNCHXL-CC13-90 Other Parts Discussed in Thread: CC1352P Hi, When I tried to connect the board to SmartRF studio, I noticed that the board is shown as unknow device, then I smelled something burning, the MCU on XDS side became too hot to…

Didn't find what you are looking for? Post a new question.