Search tips
Showing 548 results View by: Thread Post Sort by
    Answered

  • LAUNCHXL-CC1312R1: cc1312r1

    Resolved
    Part Number: LAUNCHXL-CC1312R1 Tool/software: I am trying to use the 1054 - 1315 frequency band. I have modified frequency and lo.divider and can see a reasonable carrier at 1260 Mhz ( my test frequency). I can also get communication between a launcpad…
    • Resolved

  • LAUNCHXL-CC1312R1: CC1312R1

    Part Number: LAUNCHXL-CC1312R1 Tool/software: Hi My name is Kevin Hwang in South Korea. Currently, I am developing a sensor monitoring system (sensor nodes and gateway) using the CC1312R1. The frequency band we intend to use is 940.1MHz to 946.3MHz. …
    • Answered

  • LAUNCHXL-CC1312R1: nvs location

    Resolved
    Part Number: LAUNCHXL-CC1312R1 Other Parts Discussed in Thread: SYSCONFIG Tool/software: I have created a NVS region to save module settings. I followed the example that was linked by syscfg, and it compiles OK. my save command that triggers this first…
    • Resolved
    • Answered

  • LAUNCHXL-CC1312R1: Sensor Controller Studio

    Resolved
    Part Number: LAUNCHXL-CC1312R1 Tool/software: When using LAUNCHXL-CC1312R1 and TDK InvenSense ICM-20689 6-Axis MEM breakout board on the bench, I get the following error when trying to access all 12 registers of the sensor and only can access up to 6…
    • Resolved

  • LAUNCHXL-CC1312R1: The communication distance is not ideal, and the reception sensitivity is poor

    Part Number: LAUNCHXL-CC1312R1 Tool/software: 1. The 15.4 protocol stack we use, the RF parameters are generated according to the studio software, and the transmit power is 13dBm. 2. In the previous test, in the open distance, the RSSI can be measured…

  • LAUNCHXL-CC1312R1: CC1312R1 - TRIG_ABS Start Time is considered in past

    Part Number: LAUNCHXL-CC1312R1 Hi all, I'm running into an issue where a command not being posted, the failure status is ERROR_PAST_START. After doing some testing, I found that the command is arriving to the command post with around 3ms to spare. This…
    • Answered

  • LAUNCHXL-CC1312R1: How to access XDS-110 serial number from CC1312 application?

    Resolved
    Part Number: LAUNCHXL-CC1312R1 Tool/software: I would like to access the serial number of LAUNCHXL-CC1312R JTAG debugger in run time from the active application. Is there a solution? I would like to use them as a unique ID in a network. For some reason…
    • Resolved

  • LAUNCHXL-CC1312R1: balun

    TI Thinks Resolved
    Part Number: LAUNCHXL-CC1312R1 Other Parts Discussed in Thread: CC1312R Thank you for answering [question 1] We found that the optimal load impedance for the circuit below is: optimun Load Impedance (40 + j15 Ω) @ 868MHz on swra640g.pdf page 29 So…
    • Answered

  • LAUNCHXL-CC1312R1: Error WMbus 433 (434.475 MHz) while Rx receive data with no CRC

    Resolved
    Part Number: LAUNCHXL-CC1312R1 Other Parts Discussed in Thread: WMBUS , SYSCONFIG Tool/software: I want to receive data from WMBUS 433 (434.475MHz) on CC1312R1. Data sender have this configuration: freq: 434.475 MHz symbol rate: 100 kB deviation: 50 k…
    • Resolved

  • LAUNCHXL-CC1312R1: balun desigh

    Part Number: LAUNCHXL-CC1312R1 I am designing a balun using CC1312R1. I am using swra640g.pdf to get design information. [Question 1] Where is optimun Load Impedance (40 + j15 Ω) on swra640g.pdf page 29 mean? Is it behind unburanced? [Question…

Didn't find what you are looking for? Post a new question.