Because of the Thanksgiving holiday in the U.S., TI E2E™ design support forum responses may be delayed from November 25 through December 2. Thank you for your patience.



Search tips
Showing 69 results View by: Thread Post Sort by

  • RE: LDC2114EVM: Coil Designer export to PADS fails

    Thank you for the feedback Kari. Please let us know if you have any questions or concerns. Regards, John

  • LDC2114EVM: Sensor configuration help based on custom coil design

    TI Thinks Resolved
    Part Number: LDC2114EVM Other Parts Discussed in Thread: LDC2112 , FDC1004 , LDC2114 Greetings, We are in the process of integrating a custom coil design based on the LDC2112 sensor IC. We have recently purchased a LDC2114EVM development board along with…
    • Answered

  • LDC2114EVM: Output settings

    Resolved
    Part Number: LDC2114EVM Other Parts Discussed in Thread: LDC2114 Hi Team, Our customer is currently doing research on inductive metal sensing and using the LCD1314EVM and the LCD2114EVM. He noticed that the 2 boards output the raw code differently. When…
    • Resolved
    • Answered

  • LDC2114EVM: Nominal button triggering threshold

    Resolved
    Part Number: LDC2114EVM I’m currently using the LDC2114EVM as a test for metal sensing. For design purposes i would like to lower the nominal button triggering threshold from 128 to 10. Is this possible or is there a work around I can use? The reasoning…
    • Resolved
    • Answered

  • LDC2114EVM: Signal from INTB does not change

    Resolved
    Part Number: LDC2114EVM Other Parts Discussed in Thread: LDC2114 Hello, When I was using LDC2114EVM, I found that D11 or D12 turned red. Then, I disconnected USB cable and connected it again. After that, signal from INTB does not change, though it should…
    • Resolved

  • LDC2114EVM: ESD from an equipment

    TI Thinks Resolved
    Part Number: LDC2114EVM Other Parts Discussed in Thread: FDC2114 , , FDC2114EVM , LDC2114 , LDC1314 When an electrical equipment was turned on, "Sensing Solution EVM GUI" showed "Not connected" to LDC2114LDC near the equipment. After that…
    • Answered

  • LDC2114EVM: Cannot configure LDC2114EVM through Sensing GUI

    Resolved
    Part Number: LDC2114EVM Other Parts Discussed in Thread: LDC2114 , , LDC3114-Q1 , LDC3114 Hi, I bought an EVM for the LDC2114 but unfortunately, I cannot configure the device without breaking the GUIs functionality. If I start the GUI and directly switch…
    • Resolved

  • LDC2114EVM: LDC2114EVM: No data lines on data streaming page

    Part Number: LDC2114EVM I am not seeing any data graphing on the data streaming page--no lines at all--graph is blank. I have a good connection, and I can see data in the registers. Do I have something set wrong?
    • Answered

  • RE: LDC2114EVM: out0 lights just connecting to USB port

    Resolved
    Hello, Sounds good. Let us know if you have any further issues or questions. Best Regards, Justin Beigel
    • Answered

  • LDC2114EVM: EVM doesn't store configuration settings

    Resolved
    Part Number: LDC2114EVM Other Parts Discussed in Thread: LDC2114 Hi Team I'm not able to save configuration settings made on the EVM once disconnected from USB power. This is my procedure: 1. connect EVM to USB 2. start the GUI (GUI shows "Connected…
    • Resolved

Didn't find what you are looking for? Post a new question.