TI E2E support forums
TI E2E support forums
  • User
  • Site
  • Search
  • User
  • E2E™ design support >
  • Forums
    • Amplifiers
    • API solutions
    • Audio
    • Clock & timing
    • Data converters
    • DLP® products
    • Interface
    • Isolation
    • Logic
    • Microcontrollers
    • Motor drivers
    • Power management
    • Processors
    • RF & microwave
    • Sensors
    • Site support
    • Switches & multiplexers
    • Tools
    • Wireless connectivity
    • Archived forums
    • Archived groups
  • Technical articles
  • TI training
    • Tech days
    • Online training
    • Live events
    • Power Supply Design Seminar
  • Getting started
  • 简体中文
  • More
  • Cancel


Search tips
Showing 9 results View by: Thread Post Sort by
    Answered
  • LM1877: LM1877 operating temperature

    kun liu
    kun liu
    Resolved
    Part Number: LM1877 on datasheet it says the operating temperature is 0~165,but when i decrease the voltage for device,it can work under -40 ,so i just want to know is it property,can i have some information for this ,can it be stable under -40 degree…
    • Resolved
    • over 6 years ago
    • Audio
    • Audio forum
  • Answered
  • LM1877: TCA0372 replacement

    Julian Chen
    Julian Chen
    Resolved
    Part Number: LM1877 Other Parts Discussed in Thread: TPA3111D1 , TPA3137D2 Dear all, Could we use LM1877 to replacement the TCA0372 or not? If not, could you suggest more suitable IC to us? The circuit as below, Thanks!
    • Resolved
    • over 7 years ago
    • Audio
    • Audio forum
  • LM1877 used for Audio Jack

    Kai Hsiao
    Kai Hsiao
    Other Parts Discussed in Thread: LM1877 , TPA0212 Dear Sir Currently we used LM1877 to design on R L GND Audio Jack Due to this project SPEC just only need 0.1W stereo 8ohm speaker and LM1877's total BOM space is too large Please kindly suggest…
    • over 11 years ago
    • Audio
    • Audio forum
  • Answered
  • LM1877 unused pin configuration

    toshi-e2e
    toshi-e2e
    Resolved
    Other Parts Discussed in Thread: LM1877 LM1877 is a dual power amp. When using only one ch, how do I configure unused pins? Regards, Toshi
    • Resolved
    • over 11 years ago
    • Audio
    • Audio forum
  • RE: LM1877 poor THD tuning...

    John Fedak
    John Fedak
    Hi Peter, I should have clarified better what I was looking for. I'm looking for the output waveform from the LM1877. I believe it will be clipping substaintially with 37% THD. With Vin at 12V, the LM1877 has a typical output of 1.3W/Channel at 10…
    • over 11 years ago
    • Audio
    • Audio forum
  • audio amplifier?

    kevin.huang_FJXM
    kevin.huang_FJXM
    Other Parts Discussed in Thread: LM1877 The customer is looking for an audio amplifier Requirements: HSOP package, power above 8 W, dual channel, class AB, working voltage is 13.8 v
    • over 3 years ago
    • Audio
    • Audio forum
  • LM4755: Output Noise when connected to external pre-amp through RCA

    Richard Ma1
    Richard Ma1
    TI Thinks Resolved
    Part Number: LM4755 Other Parts Discussed in Thread: LM1877 Hi Team, We found there is output noise from LM4755 when connected to external pre-amp and larger speaker through RCA cable. Usually LM4755 is connected to Speaker (~2W). My customer is…
    • over 6 years ago
    • Audio
    • Audio forum
  • RE: Audio Amplifier replacement Help

    Scott Bryson
    Scott Bryson
    Perhaps then LM1877 ?
    • over 9 years ago
    • Audio
    • Audio forum
  • About output power vs supply voltage for high power HP AMP

    yoshihiro hirata
    yoshihiro hirata
    TI Thinks Resolved
    Other Parts Discussed in Thread: TPA1517 , LM1877 , LM386 , LM4880 , TPA6205A1 Could you provide graph about output power vs supply voltage with following devices and conditions. I am maiking a search headphone amp which can drive about 120mW with these…
    • over 10 years ago
    • Audio
    • Audio forum

Didn't find what you are looking for? Post a new question.

  • Ask a new question