TI E2E support forums
TI E2E support forums
  • User
  • Site
  • Search
  • User
  • E2E™ design support >
  • Forums
    • Amplifiers
    • API solutions
    • Audio
    • Clock & timing
    • Data converters
    • DLP® products
    • Interface
    • Isolation
    • Logic
    • Microcontrollers
    • Motor drivers
    • Power management
    • Processors
    • RF & microwave
    • Sensors
    • Site support
    • Switches & multiplexers
    • Tools
    • Wireless connectivity
    • Archived forums
    • Archived groups
  • Technical articles
  • TI training
    • Tech days
    • Online training
    • Live events
    • Power Supply Design Seminar
  • Getting started
  • 简体中文
  • More
  • Cancel


Search tips
Showing 17 results View by: Thread Post Sort by
    Answered
  • RE: LM2841 startup problem

    Mark Pearson
    Mark Pearson
    Resolved
    Anston, Joe found this App Note that looks like the problem he was seeing: SNVA475A–March 2011–Revised April 2013 AN-2129 Boot Capacitor Regulation in LM25007 Constant-On-Time (COT) Converter Mark Pearson
    • over 9 years ago
    • Power management
    • Power management forum
  • RE: LM25088 whining

    EricLee
    EricLee
    Hi Paolo Or you can try the way described in this Application Report. Please refer Figure 4. Boot Capacitor Regulation in LM25007 Constant-On-Time (COT) Converter (Rev. A) Regards,
    • over 12 years ago
    • Power management
    • Power management forum
  • WEBENCH® Tools: LM25007MM(x) max frequency

    Georg Berliner
    Georg Berliner
    TI Thinks Resolved
    Other Parts Discussed in Thread: LM25007 Tool/software: WEBENCH® Design Tools Why the max frequency is now 50 kHz , before I could go much higher
    • over 6 years ago
    • Simulation, hardware & system design tools
    • Simulation, hardware & system design tools forum
  • Answered
  • RE: LM5006 no-load current

    Vijay86929
    Vijay86929
    Resolved
    Hi Dave, "AN-2129 Boot Capacitor Regulation in LM25007 Constant-On-Time (COT)" (Figure 3) shows what this regulator might do in a situation like this. In the worse case, in no load, the VOUT is expected to behave like Figure 3 in the app note cycling…
    • over 13 years ago
    • Power management
    • Power management forum
  • Answered
  • RE: LM25011 in Buck-Boost Configration

    Vijay86929
    Vijay86929
    Resolved
    Hi Stefan, In Buck-Boost mode the abs max between the VIN and GND pin is (VIN+VOUT)=24+15=39V which is really close to the abs max 42V of the IC. It is possible to that there are spikes above 42V. The buck-boost circuit current flow is different than…
    • over 13 years ago
    • Power management
    • Power management forum
  • Answered
  • RE: PWM chip selection

    John Bottrill
    John Bottrill
    Resolved
    Hi, I've attached the 2013 User's Guide for power products. Starting on page 53 you will find a selection of PWM controllers. many of these teh frequency can be varied according to external criteria. As an example if you use a UC3842 it is a simple…
    • 2013 Power Management Guide.pdf
    • over 12 years ago
    • Power management
    • Power management forum
  • Answered
  • RE: 110/220 VAC to 12 KVDC Push Pull supply?

    John Bottrill
    John Bottrill
    Resolved
    Gary, Most any of our power controllers with dual output capability will provide the control. See attached document starting at page 50 with the dual output controllers on page 53 and 54 and choose what features you want. Regards, John
    • 2013 Power Management Guide.pdf
    • over 13 years ago
    • Power management
    • Power management forum
<

Didn't find what you are looking for? Post a new question.

  • Ask a new question