Search tips
Showing 39 results View by: Thread Post Sort by

  • LM25066I-EVM: GND pad design

    TI Thinks Resolved
    Part Number: LM25066I-EVM Hi Team, Must the GND pad be placed using the same via placement method as the EVM? If so, please provide informations such as via size, via pitch, thank you.

  • LM25066I-EVM: LM25066: Random Circuit Breaker Fault & IIN_OC Fault — MOSFET Gate Stuck at ~0.7 V

    Part Number: LM25066I-EVM Other Parts Discussed in Thread: LM25066 Hello Team, Please find the attached schematic. PVT_LM25066.pdf We are using the LM25066 as a 12 V supply current limiter for a GPU in one of our products, which is currently in mass…

  • LM25066I: SN1405006 firmware update

    TI Thinks Resolved
    Part Number: LM25066I Other Parts Discussed in Thread: SN1405006 , Hi Team, What is the difference between LM25066I and SN1405006? What is the number of SN1405006 in the GUI? How to update firmware via host? Is there a guide? Regards， Haili…
    • Answered

  • LM25066I: Timer pin never goes to '0' (LOW) after insertion delay

    Resolved
    Part Number: LM25066I Tool/software: Hello, I am working on a design that uses an LM25066I. The total load is about 500 watts (12V, 40A). I have ran my design through the Excel design tool many times. The problem is that the FET is not turning ON…
    • Resolved
    • Answered

  • LM25066I: Could we use SMBus to set 4 times retry if /RETRY pin is set to latch?

    Resolved
    Part Number: LM25066I Other Parts Discussed in Thread: TIGER Hi Sir, If we do design /RETRY pin as pulled up for latch, could we use SMBus changing D9h register for retry 4 times to overwrite latch function in hardware? Thanks and Best regards,…
    • Resolved

  • LM25066I: disablling UVLO and OVLO?

    TI Thinks Resolved
    Part Number: LM25066I Hi there, is it possible to turn off the UVLO and OVLO, by connecting them respectively with VDD and GND (without additional resistors)? Thanks!
    • Answered

  • LM25066: LM25066 v.s. LM25066I

    Resolved
    Part Number: LM25066 Hi Team, The customer is asking that what is the difference between LM25066PSQ/NOPB and LM25066IPSQX/NOPB ? LM25066PSQ/NOPB is also rated at industrial temp -40 to 125c, the same as Industrial grade. Thank you. Best regards…
    • Resolved
    • Answered

  • LM25066I: GUI for Telemetry

    Resolved
    Part Number: LM25066I Other Parts Discussed in Thread: TPS544C20 , TPS53681 , , LM25066 , LM25066EVK Hi, I am looking for a GUI we could use to interface with this part (read current, temp, etc)? I am thinking something similar to Fusion Digital Power…
    • Resolved
    • Answered

  • LM25066I: I2C Address Pins ESD Protection

    Resolved
    Part Number: LM25066I Hi, we are using the LM25066i Chip and i would like to know if there is any ESD Protection on the I2C Address ADR0/ADR1/ADR2? The LM25066i is used as a hot swap but we intend to connect the ADR0 with our connector too. So that…
    • Resolved

  • LM25066I: Accuracy for LM25066i application

    TI Thinks Resolved
    Part Number: LM25066I Hi Praveen, I found there are different tolerances between different widths of trace. If the trace(vin) is 10 mil (1 oz. copper, Rs=1 mohm), we can get around -20% tolerance with 1A load. Besides, if the trace(vin) is 10 mil…

Didn't find what you are looking for? Post a new question.