Answered

• LM5018: Can't create a post

  

  Andy Delle

  Resolved

  Part Number: LM5018 On the power management forum I can't create a post.

  • Resolved

  • 29 days ago
  • Power management
  • Power management forum
Answered

• LM5018: 1.5v out no matter what

  

  Andy Delle

  Resolved

  Part Number: LM5018 Problem solved! A 1K was installed where a 10K should have been. I modified the values on an EVAL board to get 7.0 volts output. Worked fine. But the new PC board only outputs 1.5 volts. All component values checked. I see…

  • Resolved

  • 29 days ago
  • Power management
  • Power management forum
Answered

• LM5018: LM5018 alternative

  

  Jonathan Navor

  Resolved

  Part Number: LM5018 Other Parts Discussed in Thread: LM5019 , LM34926 , LM5168 Hi Team, Good day! I need your help and confirmation with the replacement for LM5018. I am checking these devices below. I checked the pin out and they are the same with…

  • Resolved

  • over 3 years ago
  • Power management
  • Power management forum
Answered

• LM5018: Output protection

  

  Jarrod Short

  Resolved

  Part Number: LM5018 Does the LM5018 require protection on the SW or FB pins when the device has no voltage applied to Vin? For reference, I'll use datasheet page 1 typical application schematic. Can the LM5018 tolerate an external voltage applied…

  • Resolved

  • over 2 years ago
  • Power management
  • Power management forum
Answered

• LM34925: Difference between LM34925 and LM5018

  

  Shuji Ishiwata

  Resolved

  Part Number: LM34925 Other Parts Discussed in Thread: LM5018 , , LM5019 , LM34926 Hi All, What is the difference between LM34925 and LM5018? As far as I checked the data sheet, I think it is the same. Customer is currently using the LM34925. What are…

  • Resolved

  • over 3 years ago
  • Power management
  • Power management forum

• LM5018: How about LM5018 Vout if without soft start circuit?

  

  user5074120

  TI Thinks Resolved

  Part Number: LM5018 Dear Sir , How about LM5018 Vout if without soft start circuit? After testing, it is found that when there is no soft start circuit, the output voltage will first rise to a value below the set voltage, then rise to the set voltage…

  • over 6 years ago
  • Power management
  • Power management forum
Answered

• LM5018: Problem with the LM5018 in design

  

  Jean Bailly

  Resolved

  Part Number: LM5018 Hi, I need, for a new design (a big production shall be following) , to use the LM5018MR/NOPB. Vin min:14V ; Vin max:60V ; Vout:12V ; Iout max: 250mA. I've tried the shematic in the datasheet, with and without the diode, (it's…

  • Resolved

  • over 7 years ago
  • Power management
  • Power management forum

• LM5018: LM5088 consult for Flybuck application

  

  Jimmy Zhou95

  TI Thinks Resolved

  Part Number: LM5018 Hi, I am reaching out for LM5018 application in Flybuck application. Do we have sink/souce capabilities specs for low side FET? And can you offer any detail for low side current protection features? Thanks! Jimmy

  • over 5 years ago
  • Power management
  • Power management forum
Answered

• LM5018: The difference of efficiency between LM5018 and LM5019

  

  K.Yaita

  Resolved

  Part Number: LM5018 Other Parts Discussed in Thread: LM5019 Hi Team, The datasheet shows efficiency of LM5019 is better than LM5018 under load current < 100mA. Left: LM5018, Right: LM5019 On the other hand, Rdson is absolutely the same value between…

  • Resolved

  • over 7 years ago
  • Power management
  • Power management forum

• WEBENCH® Tools/LM5018: The simulation results of LM5018

  

  takahiko yokota

  Part Number: LM5018 Tool/software: WEBENCH® Design Tools Hi I simulated LM5018 under Vin=34~60V, Vout=5V and Iout=150mA. I have two questions about the simulation results. 1. I could simulate I enter the condition in attached document① but…

  • over 8 years ago
  • Power management
  • Power management forum

Didn't find what you are looking for? Post a new question.