Search tips
Showing 272 results View by: Thread Post Sort by

  • LM5060-Q1: LM5060 nPGD state when EN=0

    TI Thinks Resolved
    Part Number: LM5060-Q1 Other Parts Discussed in Thread: LM74930 , LM5060 Tool/software: Hi! I have strange behavior on the output of nPGD=1.6V when EN=0 Here is my schematic: I didn't use oscilloscope to measure it, only DMM. Or it is correct?

  • LM5060-Q1: LM5060-Q1 Schematic review

    TI Thinks Resolved
    Part Number: LM5060-Q1 Other Parts Discussed in Thread: LM5060 Tool/software: Hi Team， In practical applications, customers recently discovered that three LM5060 circuits were damaged. Two of them had burn-through marks near pin 2, and one had burn-through…

  • LM5060-Q1: Vgs overvolting causing a short from Gate to Source

    Part Number: LM5060-Q1 Tool/software: Hi, The issue I have found is sometimes with certain loads (capacitative we think) Vgs overvolts, causing a directional short from Gate to Source on the main fets (FDBL9401-F085). With repeated testing, this evolved…

  • LM5060-Q1: MOS damage root cause discuss

    Part Number: LM5060-Q1 Other Parts Discussed in Thread: LM5060 Tool/software: Hi team, I am testing the LM5060 circuit OCP , I find a question, When the output pre-loading 10A by electric Load, and DC Source Current limit setting 10A. When I power on…

  • LM5060-Q1: Schematics review and how the Rsense works in this scenario

    TI Thinks Resolved
    Part Number: LM5060-Q1 Other Parts Discussed in Thread: LM76202-Q1 , LM5060 Tool/software: Hi, I have a worked a schematics using LM5060-Q1 for the below mentioned specification, does this looks fine or any improvement needed in the design. Design…

  • LM5060-Q1: Using separate Vin for driver and mosfet for LM5060 or TPS4811 or TPS2492

    TI Thinks Resolved
    Part Number: LM5060-Q1 Other Parts Discussed in Thread: LM5117 , LM5060 , TPS2493 , CSD , CSD19536KTT Tool/software: Hello, I need to add a high switch switch in the output of a variable power supply implemented using LM5117. To drive the series N-mosfet,…

  • LM5060-Q1: Difference observed between calculated Idsth value and Practical measurement

    TI Thinks Resolved
    Part Number: LM5060-Q1 Other Parts Discussed in Thread: LM5060 , TPS1663 Tool/software: Hi, As per the datasheet we have designed Idsth to 6.4A and it is verified in PSpice simulation But in actual PCB the MOSFET switches OFF at 5.3A instead of 6.4A. …

  • LM5060-Q1: Help to provide the FMEDA file of the next LM5060Q1MMX/NOPB

    TI Thinks Resolved
    Part Number: LM5060-Q1 Help to provide the FMEDA file of the next LM5060Q1MMX/NOPB

  • LM5060-Q1: protect test specification

    TI Thinks Resolved
    Part Number: LM5060-Q1 Other Parts Discussed in Thread: LM5060 , LM7480-Q1 Hi Sir, can the test specification LM5060-Q1 in the attached sections 11.9~11.20 and 11.39~11.41 meet the specification? or which test is risky? thank for your help. BCM Test Plan…

  • LM5060-Q1: Motor controller voltage spike polarity when we disconnect the BP MOSFET switch

    TI Thinks Resolved
    Part Number: LM5060-Q1 Other Parts Discussed in Thread: LM5060 Hi TI team we have designed a BMS with a bidirectional MOSFET controlled through LM5060-Q1, and implemented overcurrent protection for both the charge and discharge over currents . When overcurrent…

Didn't find what you are looking for? Post a new question.