• LM5118-Q1: Package information

  

  Frank QIN

  TI Thinks Resolved

  Part Number: LM5118-Q1 Tool/software: Hi Team, There are two package information on LM5118-Q1 datasheet, with different size. Which one should we refer? Thank you Regards, Frank

  • 4 months ago
  • Power management
  • Power management forum

• LM5118-Q1: Failure mode coverage for performing FMEDA

  

  Ashwaththi Srinivasan

  TI Thinks Resolved

  Part Number: LM5118-Q1 Other Parts Discussed in Thread: LM5118 , TPS62097-Q1 , TPS62097 Hello team, We are doing FMEDA for gateway project and we are using below components in safety critical path and I need Failure mode coverage for the same. …

  • 1 month ago
  • Power management
  • Power management forum

• LM5118-Q1: PSPICE Model Problem

  

  Danilo A.

  Part Number: LM5118-Q1 Other Parts Discussed in Thread: LM5118 Hi Team, Posting on behalf of our customer. I had some problems during Spice simulations with LM5118Q1MH PSPICE model. I'm using Ansys Circuit Designer in which SPICE simulations are…

  • 2 months ago
  • Power management
  • Power management forum

• LM5118-Q1: Functional Safety FIT Rate and FMD manual

  

  Alessandro Sanna

  TI Thinks Resolved

  Part Number: LM5118-Q1 Tool/software: Good evening, Is it possible to have the failure mode distribution rate data? Thanks in advance.

  • 3 months ago
  • Power management
  • Power management forum

• LM5118-Q1: LM5118-Q1 Load Current setting to 6A

  

  Naveen S

  TI Thinks Resolved

  Part Number: LM5118-Q1 Tool/software: Dear Team, We are using LM5118-Q1 in our design. But while simulating this circuit in webench.I'm getting the following error for 12V/6A. Your attention is highly appreciated.Meanwhile I'll calculate the values…

  • over 1 year ago
  • Power management
  • Power management forum
Answered

• LM5118-Q1: Whistling and overcurrent protection

  

  Sébastien FEUILLAS

  Resolved

  Part Number: LM5118-Q1 Other Parts Discussed in Thread: LM5118 , LM51770 Tool/software: Hi Community, I use the LM5118-Q1 for my power supply and I have two issues : I have whistling when I need 58V 2A in output (24V on input). To remove it, I have…

  • Resolved

  • 8 months ago
  • Power management
  • Power management forum

• LM5118-Q1: Output Oscillation in Transition Mode

  

  Lorenz Golob

  Part Number: LM5118-Q1 Other Parts Discussed in Thread: LM5118 Tool/software: Hello! I have a setup with the following parameters: Vout Vin Imax 8.9V 9-24V 2A All component values have been verified with the LM5118 Quick…

  • 6 months ago
  • Power management
  • Power management forum

• LM5118-Q1: Issue with Comp and SS pin

  

  Asghar Shamshir

  Part Number: LM5118-Q1 Tool/software: Hi Stefan, Hope you are doing well. I am sharing, all the waveforms issues i am facing is on comp and ss on low input 15V the output trips / clamp to 18V which was wrong as i had design it for 23V out however on higher…

  • 11 months ago
  • Power management
  • Power management forum

• LM5118-Q1: LM5118-Q1

  

  manmohan singh

  Part Number: LM5118-Q1 Hi Team, I have design 9-36Vin to 24Vout @3A power supply using Lm5118-Q1 IC, I have used the components value recommended by Webench design for the same. Everything is working fine. but during short circuit test I am still getting…

  • over 2 years ago
  • Power management
  • Power management forum

• LM5118-Q1: 48V battery system input to 45V output

  

  Will Wang47

  TI Thinks Resolved

  Part Number: LM5118-Q1 Other Parts Discussed in Thread: LM5118 , LM5176 , LM5177 , LM51772 , LM5176-Q1 Hi expert, Customer evaluating 48V automotive system, they request a 45V output to support for their audio system, output power need about 450W. …

  • over 1 year ago
  • Power management
  • Power management forum

Didn't find what you are looking for? Post a new question.