TI E2E support forums
TI E2E support forums
  • User
  • Site
  • Search
  • User
  • E2E™ design support >
  • Forums
    • Amplifiers
    • API solutions
    • Audio
    • Clock & timing
    • Data converters
    • DLP® products
    • Interface
    • Isolation
    • Logic
    • Microcontrollers
    • Motor drivers
    • Power management
    • Processors
    • RF & microwave
    • Sensors
    • Site support
    • Switches & multiplexers
    • Tools
    • Wireless connectivity
    • Archived forums
    • Archived groups
  • Technical articles
  • TI training
    • Tech days
    • Online training
    • Live events
    • Power Supply Design Seminar
  • Getting started
  • 简体中文
  • More
  • Cancel


Search tips
Showing 110 results View by: Thread Post Sort by
  • LM5160A: LM5160A

    Shachar Armon
    Shachar Armon
    TI Thinks Resolved
    Part Number: LM5160A Other Parts Discussed in Thread: LM5160 Tool/software: Hi, We need to have in the system +5.5Vdc and -5.5Vdc, we would like to implement this by DCDC Flyback, we considering use LM5160 similar to typical application in the datasheet…
    • 1 day ago
    • Power management
    • Power management forum
  • Answered
  • LM5160A: LM5160A VCC failure

    WOO JEONG HUN
    WOO JEONG HUN
    Resolved
    Part Number: LM5160A Tool/software: I would like to inquire about the defect while using LM5160A. The circuit diagram is as follows and the output waveform of the defective B/D is as follows. If 10V is forced from the outside after deleting diode…
    • Resolved
    • 6 months ago
    • Power management
    • Power management forum
  • Answered
  • LM5160A: lm5160a

    dang xiaofeng
    dang xiaofeng
    Resolved
    Part Number: LM5160A Tool/software: LM5160DNTFBKEVM评估版中,为啥原副边绕组电流以及二极管VD对地,这三个值会振荡呢
    • Resolved
    • 11 months ago
    • Power management
    • Power management forum
  • LM5160A: LM5160A

    dang xiaofeng
    dang xiaofeng
    TI Thinks Resolved
    Part Number: LM5160A Tool/software: When we use this IC as flybuck circuit .According to the inductance calculation formula, this should be the maximum value, not the minimum value limit, right?
    • over 1 year ago
    • Power management
    • Power management forum
  • Answered
  • LM5160A: LM5160

    dang xiaofeng
    dang xiaofeng
    Resolved
    Part Number: LM5160A Tool/software: 请教个问题:对于COT控制方式来说,当VFB=Vref时,就应该开通固定时间。为啥途中纹波有尖刺时,开关也在不停切换,没有导通固定的时间长。 Controlling Output Ripple & Achiev ESR Indep Constant On-Time Reg Designs (Rev. A)
    • Resolved
    • 11 months ago
    • Power management
    • Power management forum
  • LM5160A: Sporadically blow up of IC; Short circuit

    Christian Eckl
    Christian Eckl
    TI Thinks Resolved
    Part Number: LM5160A Other Parts Discussed in Thread: LM5160 Tool/software: Hi, I'm using the LM5160A module in a functional test board. Sporadically I'm struggling with defects on the IC. Local overheating always occurs at the same position in the…
    • 8 months ago
    • Power management
    • Power management forum
  • LM5160A: LM5160A maximum output power

    Nisha Yadav
    Nisha Yadav
    TI Thinks Resolved
    Part Number: LM5160A Other Parts Discussed in Thread: LM5160 , , TPS54561 Hello, I want to design 14.8V/ 1.5A power supply by using LM5160A switching regulator IC. My Input voltage will be 28V/4A and my power wattage requirement is 22.2. My only concern…
    • over 1 year ago
    • Power management
    • Power management forum
  • LM5160A: LM5160ADNT || Heat Issue || 48V TO 24V || 2A LOAD

    RAHUL RAI
    RAHUL RAI
    TI Thinks Resolved
    Part Number: LM5160A Tool/software: Hi We are using LM5160A in our design. Below is our design requirement which we done in Design. Vinput = 48V V(OUTPUT)= 24V I(LOAD) = 2A Below are issue we are facing in our PCB:- 1. We are getting…
    • 11 months ago
    • Power management
    • Power management forum
  • LM5160A: Trouble Exporting Altium Schematic for design on Webench

    Sam Cousland
    Sam Cousland
    TI Thinks Resolved
    Part Number: LM5160A I Keep getting Export failed message when I try to export the schematic from Webench Power designer for Altium Designer. see public link for design - webench.ti.com/.../SDP.cgi
    • over 1 year ago
    • Simulation, hardware & system design tools
    • Simulation, hardware & system design tools forum
  • LM5160A: Flybuck secondary output not regulating

    Paul Zwart
    Paul Zwart
    Part Number: LM5160A Other Parts Discussed in Thread: LM25183 We have a LM5160A configured in the flybuck configuration with an 8V primary voltage and aiming for a secondary output voltage of 7.5V. The following is some details on the setup: 28V VIN…
    • over 1 year ago
    • Power management
    • Power management forum
>

Didn't find what you are looking for? Post a new question.

  • Ask a new question