Search tips
Showing 60 results View by: Thread Post Sort by
    Answered

  • LM9061: Turn off time

    Resolved
    Part Number: LM9061 Tool/software: Is it possible to use a pull down resistor to ground on the output(pin 4) in order to decrease the turn off time? If so, what would be the minimum resistance allowed? My Vcc and load Voltage is 12V if that is relevant…
    • Resolved

  • LM9061-Q1: Gate driver for our selected mosfet

    Part Number: LM9061-Q1 Hi We are planning to use LM9061QDRQ1 to drive our Mosfet IAUT300N10S5N014ATMA1. We are using this for our Electro-magnetic retarder ECU board. PLease let us know if this gate driver is good to drive this Mosfet. Following is…
    • Answered

  • LM9061-Q1: Using LM9061-Q1 as a high-side Gate Driver in DC-DC Converter

    Resolved
    Part Number: LM9061-Q1 Tool/software: Hi, My question is regarding the use of LM9061-Q1 as a High-side Gate Driver for DC-DC Switching Converters. Can this be used for switching the MOSFET at 100-200kHz? In this image the output turn-on and turn…
    • Resolved
    • Answered

  • LM9061: Vcc and Load Supply

    Resolved
    Part Number: LM9061 Other Parts Discussed in Thread: LM74502H Tool/software: Hello, Can you use different supplies for Vcc and the load supply? It seems this may be possible based on Figure 19 in the datasheet, however, I see that the EVM schematic…
    • Resolved

  • LM9061: Points to consider when using this product

    TI Thinks Resolved
    Part Number: LM9061 Dear TI team Is the following understanding correct when using "LM9061"? Please advise if there are any other points to consider. ① The "ON/OFF" pin of "LM9061" can be asserted at a voltage -0.3V lower than the "Supply voltage…

  • LM9061: Delay

    TI Thinks Resolved
    Part Number: LM9061 Other Parts Discussed in Thread: TPS4811-Q1 Hi experts， Is the time for LM9061 input rising edge to switch conduction this Ton 1.5 ms? (Delay = 1.5ms?) Why delay is so high? (ADI's high side driver LTC4440 takes about 50ns…
    • Answered

  • LM9061: Bidirectional switch with reverse overcurrent protection

    Resolved
    Part Number: LM9061 Other Parts Discussed in Thread: LM5060EVAL , LM5060 Hi Experts, I wanted to try LM9061 as a b idirectional switch with reverse overcurrent protection from the datasheet page 24 and the picture below: I noticed undesirable behavior…
    • Resolved

  • LM9061-Q1: Solution to replace other

    TI Thinks Resolved
    Part Number: LM9061-Q1 Dear sir, I am planing to using the LM9061-Q1 ic for reverse polarity protection. This ic suitable for the reverse polarity protection or any other ic are there? Our requirements: Voltage: 400V DC Current:7.5A Power: …
    • Answered

  • LM9061: Overvoltage shutdown

    Resolved
    Part Number: LM9061 Other Parts Discussed in Thread: LM5060-Q1 , LM74800-Q1 , LM7480-Q1 , Hi Team, Good day! I am posting this in behalf of the customer. I have shared the full details of inquiry below: My new project is to design an electronic…
    • Resolved

  • LM9061-Q1: using LM9061 for hotswap

    TI Thinks Resolved
    Part Number: LM9061-Q1 Other Parts Discussed in Thread: LM9061 , LM5069 , LM5066 , LM5050-1-Q1 , LM5060-Q1 Dear Sir, I am using LM9061 for hotswap of two supplies from mains and Battery,to swap the Voltage of 24 Volt. I am using two LM9061 to drive…

Didn't find what you are looking for? Post a new question.