• LMG1210: Follow up to 'LMG1210 working LTSpice model with no errors' post By Catalin Muntean

  

  Ethan Zhou

  TI Thinks Resolved

  Part Number: LMG1210 Tool/software: The work example cannpt be run since the file path is incorrect. I do not have this path on my computer. Do you know how to change the file path to LMG1210_TRANS_modLTSpice.lib? I tried to use absolue path of LMG1210_TRANS_modLTSpice…

  • 1 month ago
  • Power management
  • Power management forum

• LMG1210: Amplifier to produce Negative voltage voltage pulses (Class-B or Class-D)

  

  Miguel Fernandes

  TI Thinks Resolved

  Part Number: LMG1210 Tool/software: Hello all, Working on a voltage amplifier with following requirements: - Load: capacitive 350nF max - Output: 0V to -40V (trapezoidal pulses with controlled ramp-up/down) - Slew-rate limit: 40V/us This means that…

  • 8 days ago
  • Power management
  • Power management forum
Answered

• LMG1210: LMG1210

  

  Harsh Rana

  Resolved

  Part Number: LMG1210 Tool/software: Hi, I'm using LMG1210 as half bridge driver in one of my applications in which I want switching frequency is between 1-1.5MHz. For cost saving I'm using AOD2544 MOSFET instead of using GaN FET. In half bridge configuration…

  • Resolved

  • 4 months ago
  • Power management
  • Power management forum

• RE: LMG1210: High power, High speed switching controller (Design Verification)

  

  Faiz Majeed

  ok, Thank you very much

  • 16 days ago
  • Power management
  • Power management forum
Answered

• LMG1210: Recommended Method For Adjusting Dead Time

  

  Alex Henson

  Resolved

  Part Number: LMG1210 Tool/software: Hello there, I'd like to use your LMG1210 Half-Bridge Driver for its adjustable dead time feature. However, I do have a few questions on adjusting the dead time. Looking at the datasheet, I see that the high-low…

  • Resolved

  • 1 month ago
  • Power management
  • Power management forum
Answered

• LMG1210: Dead time cannot be adjusted.

  

  Ryu Yamashita

  Resolved

  Part Number: LMG1210 Tool/software: Hi team, Circuit diagram and waveforms are attached. The first waveform is the one with the dead time adjusted to the minimum. The second waveform shows the maximum dead time. Even if we move only the falling edge of…

  • Resolved

  • 2 months ago
  • Power management
  • Power management forum
Answered

• LMG1210: About Schematic

  

  R.Fukunaga

  Resolved

  Part Number: LMG1210 Tool/software: Hi all, 1) Referring to Figure 18 in the datasheet, I am considering changing the GND of LMG1210 to the source of the Lowside FET. I think I can avoid potential fluctuation of the GND due to sense resistance. In EVM,…

  • Resolved

  • 2 months ago
  • Power management
  • Power management forum
Answered

• LMG1210: Maximum Bus Voltage

  

  Alex Henson

  Resolved

  Part Number: LMG1210 Tool/software: Hello, Can this part be used without the bootstrap diode? If that is possible what is the maximum bus voltage that can be used with the part? Thank you,

  • Resolved

  • 2 months ago
  • Power management
  • Power management forum
Answered

• LMG1210: tpw ext issue in datasheet

  

  Yuxi Liu(Tony)

  Resolved

  Part Number: LMG1210 Tool/software: Hi TIer Lmg1210 refers to tpw, ext. So, can we input pulse width exceed this value? Thank you very much.

  • Resolved

  • 2 months ago
  • Power management
  • Power management forum

• LMG1210: Full H-Bridge Configuration with EPC9099 and LMG1210

  

  Farhan Nasir

  TI Thinks Resolved

  Part Number: LMG1210 Tool/software: Hello, I am using LMG1210 gate driver ICs to drive a Full H-Bridge. I'm interested in using the LMG1210 development board, but my current rating requirements are higher than what it supports. As a solution, I’m considering…

  • 5 months ago
  • Power management
  • Power management forum

Didn't find what you are looking for? Post a new question.