Search tips
Showing 62 results View by: Thread Post Sort by

  • [FAQ] [H] High-Speed Amplifiers ADC Driver Amplifier Circuits

    Frequently Asked Questions: Amplifiers >> High Speed Amplifiers >> ADC Driver Circuits Circuit Design Considerations Transimpedance Amplifier Circuits Fully Differential Amplifier Circuits ADC Driver Circuits Other Op Amp Circuits Stab…
    • Answered

  • LMH6518: Question on clamping function

    Resolved
    Part Number: LMH6518 Hi team, My customer is looking at using the LMH6518 but has a question. Our understanding on the over-voltage clamp is it gives you the ability to set a max/min output voltage level. They do not need this function, but want to know…
    • Resolved

  • LMH6518: Will LMH6518 accept differential input?

    TI Thinks Resolved
    Part Number: LMH6518 In the datasheet, it says: The input is differential but is driven single-ended as long as the conditions of Table 6 are met, and there is good matching between the driven and undriven inputs from DC to the highest frequency of interest…

  • RE: LMH6518SQEVK: LMH6518 GUI Set Up Files

    Jacob, thank you for your time on this. I will look into use of the USB2ANY module. Regards, Joe
    • Answered

  • LMH6518: LMH6518 overdrive in DSO application

    Resolved
    Part Number: LMH6518 Hello, My customer is using LMH6518 in the 500MHz bandwiidth DSO application. A large offset (hundreds of mV) is observed when the output of LMH6518 is over drived under 500MHz. Is this normal? What can we do to solve this problem…
    • Resolved
    • Answered

  • LMH6518: Split supply +/-2.5V

    Resolved
    Part Number: LMH6518 Other Parts Discussed in Thread: OPA859 , THS4541 Hi, I am trying to find ways to interface a stage of two (pos & neg side) OPA859 used as buffers, with their CMV centered at GND, to a LMH6518 which requires a CM range of 1-4V.…
    • Resolved

  • LMH6518: How to configure the Overvoltage Clamp function of LMH6518?

    TI Thinks Resolved
    Part Number: LMH6518 Hi team, In the datasheet, LMH6518 Differential input max value is 1V. Customers would like to use Overvoltage Clamp function for avoiding the Differential input signal are bigger than 1V. Do you know how to configure the Overvoltage…
    • Answered

  • LMH6518: Specifications regarding the input swing range

    Resolved
    Part Number: LMH6518 Hi, I was going through the datasheet of the LMH6518 and i could not find what the max input swing is when the pre-amp is set to 10dB and when it is set to 30dB gain. Let's assume that we have a 0.92Vpp, the preamp is set to 10dB…
    • Resolved
    • Answered

  • LMH6518: Input common mode voltage range

    Resolved
    Part Number: LMH6518 Other Parts Discussed in Thread: OPA858 , [Michael Steffes knows this case] Hi, i am trying to interface a buffer opamp OPA858 into LMH6518 and i am having some difficulty matching the OPA858 common mode voltage (dc offset) with the…
    • Resolved
    • Answered

  • ADC3424: Guide to use LMH6518 to drive ADC3424

    Resolved
    Part Number: ADC3424 Other Parts Discussed in Thread: LMH6518 Hi Team, We are penetrate our ADC3424 in my customer in new project. Also we finally choose LMH6518 to drive ADC3424. Now customer plan to do schematic, so Can some expert help to share some…
    • Resolved

Didn't find what you are looking for? Post a new question.