• LMK03328: Loss of signal status doesn't appear to work

  

  Darius

  TI Thinks Resolved

  Part Number: LMK03328 Tool/software: Hi, I have a design with the LMK03328 which has an LVDS 20MHz primary input and a 10MHz crystal secondary input. I have found that the "loss of signal" bits do not seem to do much, they are always 0 - the reference…

  • 8 months ago
  • Clock & timing
  • Clock & timing forum

• LMK03328: Regarding EEPROM write issue

  

  Maitry Khambhati

  Part Number: LMK03328 Other Parts Discussed in Thread: USB2ANY Tool/software: Hello support team, I am using LMK03328 in my custom Intel board to provide free running clocks to different Intel FPGA Banks. I have put I2C header access to use USB2any…

  • 11 months ago
  • Clock & timing
  • Clock & timing forum
Answered

• LMK03328: I2C pull-ups with no power supplying

  

  Takayuki Yasukawa

  Resolved

  Part Number: LMK03328 Tool/software: Hi support team, Can I connect the I2C lines (SDA, SCL) of LMK03328 through pull-ups to a different power net than VDD_DIG when LMK03328 is no power supplied? According to section 8.1 of the datasheet, the Abs…

  • Resolved

  • over 1 year ago
  • Clock & timing
  • Clock & timing forum
Answered

• LMK03328: Disable output

  

  Austin Do

  Resolved

  Part Number: LMK03328 Hello team, Is there specific method to disable all outputs(only output buffer block) thru I2C command? Best Regards, Austin

  • Resolved

  • over 1 year ago
  • Clock & timing
  • Clock & timing forum

• LMK03328: Regarding Ibis Model

  

  Abhishek Kumar Singh

  TI Thinks Resolved

  Part Number: LMK03328 Hi Team I have downloaded IBIS model form website , for using with Hyperlynx but only 1.8 V output models are available . If same model is applicable for 3.3V ? If not how i can simulate for 3.3V ?

  • over 1 year ago
  • Clock & timing
  • Clock & timing forum
Answered

• LMK03328: LMK03328：Power OFF Sequence

  

  Shimizu Kensuke

  Resolved

  Part Number: LMK03328 Is there a power off sequence requirement for the LMK03328? I saw the following article. LMK03328: 電源オフ・シーケンスの標準はありますか?- クロック&タイミングフォーラム - クロック&タイミング - TI E2Eサポートフォーラム I would like to know if there are any requirements regarding…

  • Resolved

  • over 2 years ago
  • Clock & timing
  • Clock & timing forum
Answered

• LMK03328: Jitter cleaning mode

  

  Sciocp

  Resolved

  Part Number: LMK03328 Other Parts Discussed in Thread: , LMK04832 Hi, In my application, I have a clock of around 70MHz. This clock has significant jitter. I need to double this clock and filter the jitter as much as possible. I am struggling, however…

  • Resolved

  • over 1 year ago
  • Clock & timing
  • Clock & timing forum
Answered

• LMK03328: Reset the device

  

  Takayuki Yasukawa

  Resolved

  Part Number: LMK03328 I have a question about I2C access failures. In another thread, we found an I2C access failure event with a frequency of 1/1000. LMK03328: POR spec - Clock & timing forum - Clock & timing - TI E2E support forums We too have confirmed…

  • Resolved

  • over 1 year ago
  • Clock & timing
  • Clock & timing forum
Answered

• LMK03328: Footprint data

  

  Shoo Saga

  Resolved

  Part Number: LMK03328 Hi Team, Could you share footpirnt data like below? I didn't find it in the datasheet. Thanks, Shoo

  • Resolved

  • over 1 year ago
  • Clock & timing
  • Clock & timing forum
Answered

• LMK03328: Startup time in jitter cleaning mode

  

  jdery

  Resolved

  Part Number: LMK03328 Hello, In my application, I have a clock with significant jitter. I need to double this clock and filter the jitter. I am currently prototyping on the LMK03328EVM development kit. With my current settings, the LMK03328 provides…

  • Resolved

  • over 1 year ago
  • Clock & timing
  • Clock & timing forum

Didn't find what you are looking for? Post a new question.