• LMR14006: LMR14006 PCB placement

  

  Bob Shaikhvand

  TI Thinks Resolved

  Part Number: LMR14006 Hi, Please review our LMR14006XDDCR (U13) placement and layout for EMI integrity. Attached are the schematic and layout. Thank you, Bob

  • over 4 years ago
  • Power management
  • Power management forum

• LMR14006: Searching TI solution

  

  Kygo Cheng

  TI Thinks Resolved

  Part Number: LMR14006 Hi Team, There is a good new that Customer is searching TI solution Do we have a product that can compete with "MPQ2451DJ-AEC1-LF-Z" ? 1. It seem that LMR14006can fight with MPQ2451DJ-AEC1-LF-Z ,is there anything I need to…

  • over 3 years ago
  • Power management
  • Power management forum
Answered

• LMR14006: Maximum and minimum voltage at Pin CB

  

  vaibhav waman

  Resolved

  Part Number: LMR14006 Hello Team, we need bootstrap voltage for our MOSFET drive purpose. As we are already using LMR14006XDDCR in same circuit, can we use charge from CB capacitor ? In that case what is the maximum and minimum voltage can appear…

  • Resolved

  • over 3 years ago
  • Power management
  • Power management forum

• LMR14006: LMR14006

  

  DHIREN SAHOO

  TI Thinks Resolved

  Part Number: LMR14006 Hi, I need the formulae for calculate the power dissipation of LMR14006 DCDC buck converter. what s the formula . Please suggest . Thanks & Regards Dhiren Sahoo

  • over 5 years ago
  • Power management
  • Power management forum

• LMR14006: webench sch

  

  [FAE] Andrew Wang

  TI Thinks Resolved

  Part Number: LMR14006 Hi Team, Please help double check if this webench recommended sch looks ok? Customer found LMR14006Y EVM has similar spec, but different in component values, so want to verify if anything could to optimize, thanks! https:/…

  • over 4 years ago
  • Power management
  • Power management forum
Answered

• LMR14006: Different font style on body marking

  

  Grace Tan

  Resolved

  Part Number: LMR14006 Hi TI Team, can you please check and advise if this is normal ? Same MPN, Same COO - MY, different Datecode, but font style on body marking shows differently for the number "1"

  • Resolved

  • over 3 years ago
  • Power management
  • Power management forum
Answered

• LMR14006: Specifications for freewheeling diode

  

  Nicholas Ipri1

  Resolved

  Part Number: LMR14006 Are there any recommendations for selecting the freewheeling diode other than max voltage and forward current? I am especially interested in any requirements for reverse recovery time? I have an existing design that uses a ZHCS400…

  • Resolved

  • over 4 years ago
  • Power management
  • Power management forum

• LMR14006: Question about SHDN voltage and current limit of LMR14006

  

  Masaharu Takahashi

  TI Thinks Resolved

  Part Number: LMR14006 Other Parts Discussed in Thread: LMR14030 Hi, Team. could you tell me below? is there hysteresis on SHDN pin ? can we know the current limit as min and max? Customer wants to select the inductance by getting know how…

  • over 6 years ago
  • Power management
  • Power management forum

• LMR14006: Need large signal voltage gain value of OP-Amp IC LMR14006XDDCR

  

  shanmuga suriya V

  TI Thinks Resolved

  Part Number: LMR14006 Hi, Need below mentioned electrical characteristics of IC LMR14006XDDCR 1.Switch leakage current 2.Feedback pin bias current 3.Minimum OFF-time

  • over 3 years ago
  • Power management
  • Power management forum

• LMR14006: Programmable output DC-DC converter

  

  Vladimir Laukh

  TI Thinks Resolved

  Part Number: LMR14006 Hey! I'm implemeting design mentioned in the article https://www.ti.com/lit/an/slyt777/slyt777.pdf?ts=1597909097823 (Fig.10) with LMR14006 converter. DC output of the converter is set by PWM fed to FB pin through resistors…

  • over 5 years ago
  • Power management
  • Power management forum

Didn't find what you are looking for? Post a new question.