Search tips
Showing 26 results View by: Thread Post Sort by
    Answered

  • LMT85: Could you tell me where Thermal Response is faster？

    Resolved
    Part Number: LMT85 Hi, support team My customer has the questions as follow: Surface mounted Temperature sensor, such as LMT85DCKT or TMP235AEDCKT. Top temperature (surface air temperature), bottom temperature (Substrate temperature in contact with bottom…
    • Resolved

  • LMT85: Accuracy range

    TI Thinks Resolved
    Part Number: LMT85 Hi, Can you please confirm that the accuracy of part will not vary more than +/-2.7DegC over the whole temperature range of -50DegC to +150DegC. as the datasheet says as below BR, Rahul
    • Answered

  • LMT85: Power supply and Output voltage relationship

    Resolved
    Part Number: LMT85 Hi, Power supply for LMT85 is rated for (+1.8V to +5.5V) and from the Transfer Table of the datasheet i can see the Vout at -50C is 1955mV~1.9V. Just trying to understand if I operate the device at 1.8V then also the Transfer table values…
    • Resolved

  • LMT85: About Pin out of LMT84 / LMT85 / LMT86 / LMT87 (DCK package)

    TI Thinks Resolved
    Part Number: LMT85 hi, Is the correct functional behaviour of LMT85-Q1 impacted if inadvertently PIN5 has been connected to VDD instead of GND? if yes, to which extend? thanks, Ulrike
    • Answered

  • RE: LM20: next gen of LM20

    Resolved
    Hello Given, The link below shows all analog sensors which support -40C to 150C and are available in SC70(DCK) 5 pin package. TMP9A00-EP is the only device with the same gain of -11.77mV/C. If you can use a different sensor gain, TMP235 is a good candidate…
    • Answered

  • LMT85: LMT85 capacitor loads

    Resolved
    Part Number: LMT85 Hi Engineers, In LMT85 datasheet, when driving a switched sampling input on an ADC. It may necessary to add some filtering to minimize noise coupling. And there are two methods we can see. I'm not very sure the application for the two…
    • Resolved
    • Answered

  • MSP430G2553: Pairing the LMT85-Q1 analog temperature sensor to the MSP430G2553

    Resolved
    Part Number: MSP430G2553 Other Parts Discussed in Thread: LMT85-Q1 , MSP-FET This is my circuit. I'm feeding the LMT85-Q1 from the P2.1 of the MCU. Pin 2 on the MCU (A0) is used for reading the output from the sensor. #include <msp430.h> /** …
    • Resolved
    • Answered

  • LMT85-Q1: temperature lookup table file

    Resolved
    Part Number: LMT85-Q1 Hi TI support, I am looking for the lookup table to calculate temperature with input reading from the LMT85-Q1, data sheet says the table is available from a link to TI site under software/tools, but it is disabled for this product…
    • Resolved

  • ADS1248: Interfacing the LMT85 as a cold junction sensor

    Part Number: ADS1248 Other Parts Discussed in Thread: LMT85 , , LMT70 , ADS1220 , ADS124S08 An ADS1248 design uses an LMT85 as the cold junction sense for thermocouple measurement. The ADS1248 is unipolar supplied. In order to comply with ADS1248 measurement…
    • Answered

  • LMT85: Interfacing to an ADS1248, raising ground to be 100 mV or greater above AVSS for a differential measurement.

    Resolved
    Part Number: LMT85 Other Parts Discussed in Thread: ADS1248 , I am using an LMT85 as a cold junction sensor (actually two) for thermocouple measurements. The LMT85 is interfaced to an ADS1248. It is required, that the PGA AINN or negative input of the differential…
    • Resolved

Didn't find what you are looking for? Post a new question.