Search tips
Showing 10 results View by: Thread Post Sort by
    Answered

  • LP2950-N: Cannot Find the TI PN for the formed lead version / T&R package of this product

    Resolved
    Part Number: LP2950-N Hi, I have a customer asking for the formed lead version of the LP950ACZ-5.0/NOPB that comes in a tape and reel package? I am looking through TI.com for the PN but cannot find it. Can you provide any guidance? Thank you!
    • Resolved

  • LP2950-N: Altitude

    TI Thinks Resolved
    Part Number: LP2950-N Hi, Good Day. Does LP2950-N meets 30k ft altitude specs? Thank you very much. Best Regards, Ray Vincent

  • LP2950-N: LP2950CDTX-3.3/NOPB issue

    Part Number: LP2950-N Hi team, My customer is using LP2950CDTX-3.3/NOPB to covert 12V to 3.3V in their project, but they failed the radiation spurious test in the FCC certification test of BT. The reason for asking us about this question is because the…
    • Answered

  • LP2951: Output capacitor type

    Resolved
    Part Number: LP2951 Other Parts Discussed in Thread: LP2950-N , , LP2950 Dear e2e support, As it's not mentioned in the LP2950/51 datasheet (while it is in the LP2950-N, LP2951-N datasheet), could you confirm that the output capacitor type could be either…
    • Resolved

  • REG113: ESD specification of REG113EA-3.3/2K5

    TI Thinks Resolved
    Part Number: REG113 Other Parts Discussed in Thread: LP2950-N , TPS719 , TLV717P , LM9076 , LP5900 , TLV766-Q1 , TPS746-Q1 , LP3988 , LP3981 , TPS745-Q1 , LP2986 , TPS794 , , LP2989 , TLV707 , TLV733P , TPS785-Q1 , TPS7A60-Q1 , LMS1585A , LP3872 Hi team, My customer want…
    • Answered

  • LP2950-N Junction-to-Ambient thermal resistance for TO-252

    Resolved
    Other Parts Discussed in Thread: LP2950-N Hi team, Is there any information on what the junction-to-ambient thermal resistance is for the TO-252 package for the LP2950-N? Specifically the LP2950CDT-3.3. The datasheet mentions junction-to-ambient thermal…
    • Resolved
    • Answered

  • RE: ADC78H90: Analog/Digital Supplies to ADC

    Resolved
    Hi Josef, Yes, your understanding is correct. I also want to point out that the 0.1uF and 1uF capacitors near the regulator depend on the regulator requirements, and not the ADC. The LP2950-N requires a minimum of 1uF, but also has an ESR requirement…

  • LDO that starts below 1.6 VDC

    Other Parts Discussed in Thread: LP2951-N , LP2950-N , LM9076 I have an odd requirement: * Vin 1.5VDC to 26VDC * Vout anything from 1.0 to 5 VDC; need not be regulated below 5 VDC, but I need to to start at 1.5 VDC in, and get 1.0 VDC Out * 40 mA * prefer…
    • Answered

  • LM337IMP Output Has 180mV Sawtooth Ripple

    Resolved
    Other Parts Discussed in Thread: LM317 , LM337 , LP2950 , LM337-N I have used the LM317 and LM337 regulators many times in this configuration. In this case the LM337 output is set to 9V. Superimposed is a sawtooth with 180mV amplitude. The frequency and amplitude…
    • Resolved

  • LP2951CM/NOPB

    Other Parts Discussed in Thread: LP2951 , LP2951-N , LP2950 Dear all, Because of the large number of LP2951 type numbers I'm not shure if the (output programmable) LP2951CM/NOPB type has SENSE and Vtap voltage divider resistors inside the package. I assume…

Didn't find what you are looking for? Post a new question.