Search tips
Showing 10 results View by: Thread Post Sort by

  • LP2986: Shutdown and Error pin logic

    TI Thinks Resolved
    Part Number: LP2986 Hi Team, Our customer would like to clarify about the function of the output and shutdown pins of LP2986IM-5.0/NOPB. According to our customer, When the SHUTDOWN pin is LOW (Regulator Disabled), is the Dropout Detection ignored/disabled…

  • LP2986: Searching TI solution

    Part Number: LP2986 Other Parts Discussed in Thread: TPS7A25 Hi Team, There is a good news that we have a chance to replace " CAT6201 " Do we have a solution to replace " CAT6201 " ? The URL below is "CAT6201" datasheet IC000788000…

  • LP2986: LP2986 Programmable Vout ratings enquiry

    TI Thinks Resolved
    Part Number: LP2986 Hi, i'm looking for a wide Vin low noise LDO which is able to take in 9V+ Vin & i've found the LP29856, unhowever on my Vout i'll need to get 8.4V/200mA. Is possible for me to get this outing ratings even it's exceeding 5V Vout?…

  • LP2986: Leakage current (Vin to Vout) when device is shutdown via SHUTDOWN pin

    TI Thinks Resolved
    Part Number: LP2986 What is the standby current for this device? This TI document (Understanding the Terms and Definitions of LDO Voltage Regulators ( ) defines the term standby current as follows: "Standby Current- Standby current is the input current…

  • LP2986: External resistor for adjustable output voltage

    TI Thinks Resolved
    Part Number: LP2986 Hi, A question about LP2986 external resistor for adjustable output voltage, on data sheet, 8.2.2.1 "The resistor connected between the FEEDBACK pin and ground pin should be 51.1 Kohm." Can I change it to the other value…

  • REG113: ESD specification of REG113EA-3.3/2K5

    TI Thinks Resolved
    Part Number: REG113 Other Parts Discussed in Thread: LP2950-N , TPS719 , TLV717P , LM9076 , LP5900 , TLV766-Q1 , TPS746-Q1 , LP3988 , LP3981 , TPS745-Q1 , LP2986 , TPS794 , , LP2989 , TLV707 , TLV733P , TPS785-Q1 , TPS7A60-Q1 , LMS1585A , LP3872 Hi team, My customer want…
    • Answered

  • LP2986 and Schottky protection

    Resolved
    Other Parts Discussed in Thread: LP2986 I have some difficulties to choose a Schottky diode to protect my LP2986. Vin is a battery between 0V and 14.7V, I have two LP2986, one @ 3.3V and a another @ 5V. What are the criteria for choosing my diode ? …
    • Resolved

  • RE: LMG1020: Selection of voltage regulator for gate driver power supply

    Hi Hitesh, LMG1020 takes 5V typical but can accept as low as 4.75V and as high as 5.4V under the recommended operating conditions of the lmg1020 datasheet page 4. Any adjustable regulator capable of this range and regulated to 5% is compatible with LMG1020…

  • TIDA-00961: IC FOOT PRINT NOT MATCHING

    TI Thinks Resolved
    Part Number: TIDA-00961 Hi, Can you please confirm the component U304 used in the circuit is LP2986AIMM-3.3/NOPB. The pitch mentioned in the gerber is 0.65mm which is for the SSOP Package ICs only. But no SSOP packages are available for LP2986 ICs .Only…
    • Answered

  • Current ratings of SN74LVC2G53

    Resolved
    Other Parts Discussed in Thread: SN74LVC2G53 , LP2986 Hi, I am confused to know current ratings of SN74LVC2G53. how much current it would take when On state. how much current it would take when switching? also would it hold the switching current? how much…
    • Resolved

Didn't find what you are looking for? Post a new question.