• LP38690: ESD Sensitivity of LP36890

  

  TI-CSC

  TI Thinks Resolved

  Part Number: LP38690 Hello E2E Experts, Good day. HBM is given on the datasheet, however, I would like to ask: What is the CDM ESD sensitivity of the LP36890 voltage regulator? Thank you in advance. Regards, CSC

  • over 1 year ago
  • Power management
  • Power management forum
Answered

• LP38690：Questions about footprints

  

  ? ??

  Resolved

  Part Number: LP38690 Questions about footprints. Please tell me the positional relationship between the parts and the land pattern. The positional relationship is unknown in the data sheet. TO-252 Package NS Package Number TD03B

  • Resolved

  • over 2 years ago
  • Power management
  • Power management forum
Answered

• LP38690-ADJ: P2P Drop in replacement with Lower VO MIN?

  

  Chad Crosby

  Resolved

  Part Number: LP38690-ADJ Other Parts Discussed in Thread: LP38500-ADJ , , TPS7A8101-Q1 , TLV767-Q1 , TPS74801-Q1 , TPS7A54-Q1 , TPS7A52-Q1 Hi, I'm looking for a regulator with the same pinout as the DFN6 package of this device, but with VO at least able to…

  • Resolved

  • over 2 years ago
  • Power management
  • Power management forum

• LP38690: Inquire about the cause of the defect

  

  JH Shin

  TI Thinks Resolved

  Part Number: LP38690 Hello, My customer is using LP38690SD-3.3/NOPB for the optical module application. The following defect occurred in LP38690SD-3.3/NOPB while using the optical module. - Input voltage = 5V, Typical load current = 230mA - The output…

  • over 3 years ago
  • Power management
  • Power management forum
Answered

• LP38690: SN6505 equivalent

  

  robin gangopadhya18

  Resolved

  Part Number: LP38690 IS THERE A 12 v version of SN6505 push pull transformer driver?

  • Resolved

  • over 3 years ago
  • Power management
  • Power management forum

• LP38690-ADJ: Reference voltage is 1.8V instead of 1.25V

  

  Ahmed Mostafa1

  TI Thinks Resolved

  Part Number: LP38690-ADJ Hi , I'm using this part LP38690SDX-ADJ, with a 6.3V in and 5V out. My top feedback resistor is 30.9k, and bottom feedback resistor is 10k. I'm using a 4.7uF input and output ceramic cap. Upon measuring the output,…

  • over 4 years ago
  • Power management
  • Power management forum
Answered

• LP38690: load regulation

  

  Ryuuichi machida

  Resolved

  Part Number: LP38690 Hi, I would like you to confirm whether spec of load regulation is correct or not. Because, max of load regulation is 5V in worst case. I think this is too big, so could you confirm about above ? BR,

  • Resolved

  • over 5 years ago
  • Power management
  • Power management forum

• LP38690: SNS input resistance

  

  Falk Alicke

  TI Thinks Resolved

  Part Number: LP38690 Hi, The LP38690 shows the SNS input stage to use an internal resistor divider R1/R2, but it does not spec the resistor values or input leakage. How large is the internal resistance R1+R2, and is there any other leakage spec? I am…

  • over 6 years ago
  • Power management
  • Power management forum

• LP38690: Stability and Output Capacitor ESR

  

  John Garrett

  Part Number: LP38690 I have a customer who is using a LP38690 with Vin = 6.6V from a 400kHz switching power supply and Vout = 5.0V. They are using a 4.7uF ceramic capacitor on the input and both a 4.7uF, 0603 located right at the output pin of the part and…

  • over 6 years ago
  • Power management
  • Power management forum

• LP38690 input slew rate

  

  K.Hamamoto

  Other Parts Discussed in Thread: LP38690 HI Does LP38690 have any specification for slew rate of the input voltage? Our customer are going to put the resistor for current limiting resistor on the input line. ( under dozens ohm) It will be concerned with…

  • over 9 years ago
  • Power management
  • Power management forum

Didn't find what you are looking for? Post a new question.