Search tips
Showing 13 results View by: Thread Post Sort by

  • MSP430G2312:Voltage divider resistor (inflow current required for COMP)

    Part Number: MSP430G2312 msp430g2312に関する確認 Peripheral_COMP で私は電圧を監視したいと思います 動作は約5Vの 電源のためのメガオーダーの抵抗電圧分圧器で不安定です。 また、 データシートのCOMPカラム I(DD)=45μA 部分圧が10KΩ程度でないと難しいですか? 電圧分割抵抗の適切な桁を教えてください。
    • Answered

  • MSP430G2312: I/O Port Question

    Resolved
    Part Number: MSP430G2312 Hi Team, Posting for our customer. When the port is set to I/O input and internal pull-up and pull-down resistors are enabled, how much current does the port sink and source due to contact on/off when the mechanical contact switch…
    • Resolved

  • MSP430G2312:the filter capacitor for chattering countermeasures

    Part Number: MSP430G2312 MSP430G2312とMSP430Gシリーズに関する質問があります。 ポートがI / O入力に設定され、内部プルアップおよびプルダウン抵抗が有効になっている場合 機械的接触スイッチが外部から直接接続されている場合、オン/オフの接触によるポートのシンクとソースの電流はいくつありますか? また、同じ仕様で、チャタリング対策のためのフィルタコンデンサの適切な値は いくつですか? ご不便をおかけして申し訳ございませんが、ご回答いただき、ありがとうございます…
    • Answered

  • how to tell the pin1 from the top of MSP430G2312

    Resolved
    Other Parts Discussed in Thread: MSP430G2312 Hello, Seems this question silly, I have few MSP430G2312 already soldered on the board, there is a dot on the mark. is the Dot on the right bottom mark pin1. and the pin number counter clock. please confirm…
    • Resolved

  • Using EZ430 kit to program MSP430G2312

    Other Parts Discussed in Thread: MSP430F2012 , MSP430G2312 , EZ430-F2013 Wanting to replace MSP430F2012 device with MSP430G2312 for additional memory and cost considerations. In the past, we have programmed the F2012 on our target board using the Ez430 USB…

  • MSP430FR2512: How to design the hardware of a touch key in my application?

    TI Thinks Resolved
    Part Number: MSP430FR2512 Other Parts Discussed in Thread: MSP430G2312 , MSP-FET430UIF Hi TI employee, We need a touch Key in a consumer-electronics application which is powered by a cell-battery( CR2032）. At first , we chose MSP430G2312 , use pin-Oscillator…
    • Answered

  • G2312 family SVSIN reset - from where?

    Resolved
    Other Parts Discussed in Thread: MSP430G2312 Hi Folks, I have a circuit using an MSP430G2312 which is showing unexpected reset behaviour. These chips have a BOR brown out reset and a SVS supply voltage supervisor. Looking at the SVS module, the default…
    • Resolved
    • Answered

  • ccs_setup_ 5.5.0.00077 Offline installer error

    Resolved
    Other Parts Discussed in Thread: CC430F5123 , CC430F5125 , CC430F5133 , CC430F5135 , CC430F5137 , CC430F5143 , CC430F5145 , CC430F5147 , CC430F6125 , CC430F6126 , CC430F6127 , CC430F6135 , CC430F6137 , CC430F6143 , CC430F6145 , CC430F6147 , MSP430AFE221 , MSP430AFE22…
    • Resolved
    • Answered

  • RE: CCS/EVMK2G: Compilation Failure: Missing source file "ti/drv/pa/pa.h"

    Resolved
    I ran into some issues using pdkProjectCreate script. See attached text files for output of both scripts i.e. pdkProjectCreate and pdksetupenv. The pdkProjectCreate script created a folder called MyExampleProjects but it was empty. The script appears…

  • RE: Compiler/MSP430FR2633: Compilation Error: error #18: expected a ")"

    OK, got an .rl file. See attached. The line in question in this file is line 42960, __bis_SR_register(GIE). If you look, it replaces that line with the following: __asm__ __volatile__ ("bis.w %0, SR { nop" : : "ri"((unsigned int) (0x0008)) );…

Didn't find what you are looking for? Post a new question.