Search tips
Showing 20 results View by: Thread Post Sort by

  • MSPM0L1305-Q1: The performance of ADC at around 100°C

    Part Number: MSPM0L1305-Q1 Other Parts Discussed in Thread: MSPM0L1305 During recent high-temperature testing, we observed occasional fluctuations in the analog values sampled by the ADC of the MSPM0L1305 when the ambient temperature reached approximately…

  • MSPM0L1305-Q1: MSPM0L1305

    TI Thinks Resolved
    Part Number: MSPM0L1305-Q1 Other Parts Discussed in Thread: MSPM0L1305 , SYSCONFIG Tool/software: MSPM0L1305 Flashing Issue I am trying to program an MSPM0L1305 microcontroller using an XDS110 debugger in Code Composer Studio (CCS 20.0.2) , but I…
    • Answered

  • MSPM0L1305-Q1: How to know the wake up source?

    Resolved
    Part Number: MSPM0L1305-Q1 Tool/software: Hi Champs, Is there any register that can identify the wake up source? I'm using standby low-power mode with __WFI() function. But I faced an unexpected wake up situation, so I want to know which source caused…
    • Resolved
    • Answered

  • MSPM0L1305-Q1: Optimization level recommended by ccs

    Resolved
    Part Number: MSPM0L1305-Q1 Other Parts Discussed in Thread: MSPM0L1305 Tool/software: hi,team For mspm0l1305, what is the optimization level recommended by ccs?
    • Resolved

  • MSPM0L1305-Q1: Pin Injection Limit for ADC Measurement

    Part Number: MSPM0L1305-Q1 Tool/software: Hi, I've been reading the datasheet for the MSPM0L1305-Q1. I'm looking for information on 'pin injection limit for ADC measurement'. I can't find anything directly mentioning and limit's on the ADC pins expect…

  • MSPM0L1305-Q1: The BSL upgrade is abnormal and cannot be restored

    TI Thinks Resolved
    Part Number: MSPM0L1305-Q1 Tool/software: hi，Team We use MSPM0L1305-Q1 for in-vehicle projects. The BSL upgrade function was used in the project, and the configuration is as follows. We discovered the following problems during the development 1. If…

  • MSPM0L1305-Q1: reason for limiting flash size by 8B from full address range

    TI Thinks Resolved
    Part Number: MSPM0L1305-Q1 Other Parts Discussed in Thread: MSPM0L1305 Tool/software: Hi TI Team, In original TI linker file for MSPM0L1305 following Flash range is defined:     FLASH (RX) : origin = 0x00000000, length = 0x00007FF8 What is the…

  • MSPM0L1305-Q1: FCL function

    Part Number: MSPM0L1305-Q1 Tool/software: Good day, colleagues, 1. If these two PIN pins are used as timer function. Is it necessary to increase pull-up resistance for them? When the MCU is reset, these two PIN default output is high voltage or low…
    • Answered

  • MSPM0L1305-Q1: MSPM0L fails to connect to XDS110 debugger in Customer board

    Resolved
    Part Number: MSPM0L1305-Q1 Other Parts Discussed in Thread: UNIFLASH Tool/software: hi,team Please help take a look at the debug connection issue of the mspm0l program. When connecting to our own motherboard via the XDS110 on the MSPM0+ development…
    • Resolved

  • MSPM0L1305-Q1: Lin speed with no crystal

    Part Number: MSPM0L1305-Q1 Hello, On the overview page of this device, we show that we can support 9600 baud LIN communication without a crystal. I have a request to see if we can support 11K and even up to 19.2K without a crystal. Are these speeds…

Didn't find what you are looking for? Post a new question.