Answered

• MSPM0L1306: can Vref- connect to negative voltage?

  

  Frank(EP) Liu

  Resolved

  Part Number: MSPM0L1306 Tool/software: hi, the input signal is +/-100mV, can i connect Vref- to negative voltage for ADC? So, MCU can measure the signal level. BR, frank

  • Resolved

  • 2 months ago
  • Arm-based microcontrollers
  • Arm-based microcontrollers forum
Answered

• MSPM0L1306: Does MSPM0L1306 support hardware SMI[MDC/MDIO] interface?

  

  W Z

  Resolved

  Part Number: MSPM0L1306 Tool/software: Does MSPM0L1306 support hardware SMI[MDC/MDIO] interface which is used for PHY control? And does TI have the example code for SMI[MDC/MDIO] interface

  • Resolved

  • over 1 year ago
  • Arm-based microcontrollers
  • Arm-based microcontrollers forum
Answered

• MSPM0L1306: Error in datasheet?

  

  Davin Nicholas

  Resolved

  Part Number: MSPM0L1306 Tool/software: In the MSPM0L1306 datasheet on page 39 where is describes the timers it does list QEI support. However, the parts listed in the datasheet don't have any timer modules that support this interface. Maybe this reference…

  • Resolved

  • 4 months ago
  • Arm-based microcontrollers
  • Arm-based microcontrollers forum

• MSPM0L1306: TRACEID Value in MSPM0L1306

  

  Rahul Patel

  Part Number: MSPM0L1306 Tool/software: TRACEID is read as 0x00000000, values should change with different boards or not?

  • over 1 year ago
  • Arm-based microcontrollers
  • Arm-based microcontrollers forum
Answered

• MSPM0L1306: MSPM0L1306: In MSPM0L1306 Auto-Baud for LIN

  

  santhosh prem

  Resolved

  Part Number: MSPM0L1306 Hi Team, Could you please help me with some calculations? I have 5 segments of gBitTimes[gNumCycles].posEdge and gBitTimes[gNumCycles].negEdge it is from the LIN Responder code . I've been trying to calculate the baud rate, but…

  • Resolved

  • over 1 year ago
  • Arm-based microcontrollers
  • Arm-based microcontrollers forum

• MSPM0L1306: MSPM0L Silicon Defect

  

  Patrick Townsend

  Part Number: MSPM0L1306 Other Parts Discussed in Thread: , SYSCONFIG Tool/software: GTS found a new/undocumented error in the MSPM0L1306 microcontroller related to the clock (SYSCLK) that is feeding UART0. Rob is developing code and testing with the LP…

  • 3 months ago
  • Arm-based microcontrollers
  • Arm-based microcontrollers forum
Answered

• MSPM0L1306: ADC Result

  

  Carwyn Hancock

  Resolved

  Part Number: MSPM0L1306 Other Parts Discussed in Thread: SYSCONFIG Tool/software: I'm trying to learn and understand more of the MSPM0 boards. I'm attempting to use a potentiometer to adjust the toggle speed of the RGB LED to switch between R, G and B…

  • Resolved

  • 4 months ago
  • Arm-based microcontrollers
  • Arm-based microcontrollers forum

• MSPM0L1306: UART0 incorrect data

  

  Tom Schultz

  Part Number: MSPM0L1306 Other Parts Discussed in Thread: SYSCONFIG Tool/software: Team, Posting on behalf of my customer. Problem: At maximum processor voltage (3.3V), the following sequence causes incorrect data (two extra 1 bits are inserted in…

  • 4 months ago
  • Arm-based microcontrollers
  • Arm-based microcontrollers forum

• MSPM0L1306: MSPM0L1306SRHBR

  

  Chintan Patel

  TI Thinks Resolved

  Part Number: MSPM0L1306 Other Parts Discussed in Thread: SYSCONFIG Tool/software: Dear Support Team, We are encountering an issue where the code gets stuck in the clock initialisation section. Out of 110 units, 10 units are affected by this problem…

  • 4 months ago
  • Arm-based microcontrollers
  • Arm-based microcontrollers forum
Answered

• MSPM0L1306-Q1: Is the NRST pin bidirectional

  

  Abdulkader Al-Obaidi

  Resolved

  Part Number: MSPM0L1306-Q1 Other Parts Discussed in Thread: MSPM0L1306 Tool/software: Is the NRST pin(3) on MSPM0L1306 bidirectional? The concern I have is if MSPM0L1306 can internally pull NRST pin to ground it can create a shoot through from the IC…

  • Resolved

  • 2 months ago
  • Arm-based microcontrollers
  • Arm-based microcontrollers forum

Didn't find what you are looking for? Post a new question.