Search tips
Showing 20 results View by: Thread Post Sort by
    Answered

  • RE: PCM1860-Q1: PCM1860-Q1 [INT] pin type

    Resolved
    Thank you for your early reply. As a confirmation, is it only PCM1860-Q1 = Hardware control typ that the logic of INT pin is reversed? Is the Software control typ such as PCM1862-Q1 the same?

  • RE: PCM1860-Q1: Supporting Fs=16kHz with system clock of 768fs in slave mode

    Hello Zak, Thank you for your comments. I understand the table 12 says PCM1862-Q1 and PCM1863-Q1, but it is also applicable for PCM1860-Q1. Best Regards, Yoshikazu Kawasaki

  • [FAQ] PUREPATHCONSOLE: Software lookup table for audio devices

    TI Thinks Resolved
    Part Number: PUREPATHCONSOLE Tool/software: A table with links to all the software needed for audio devices and their EVMs. Find the device(s) of interest in the table and use the links to request access to the software you need. Product or…
    • Answered

  • PCM1860-Q1: Analog input mix support

    Resolved
    Part Number: PCM1860-Q1 Other Parts Discussed in Thread: PCM1860 , PCM1865 , PCM1863 , PCM1862 , PCM1864 Hi TI, Does PCM1860 support analog input mix? I have checked the block diagram as below. It seems there are mix and mux function for analog input…
    • Resolved
    • Answered

  • PCM1864-Q1: question about configuring 1864 and 1862 into TDM mode

    Resolved
    Part Number: PCM1864-Q1 Other Parts Discussed in Thread: PCM1864 , PCM1862 Dear expert, I have 5 channel audio data (three microphone, and one stereo FM), due to the limited I2S/TDM port available on my application processor, I want to use PCM1864 …
    • Resolved
    • Answered

  • PCM1861-Q1: PCM1861

    Resolved
    Part Number: PCM1861-Q1 Other Parts Discussed in Thread: PCM1862 , PCM1861 Hi I am planning to use PCM1861-Q1 110 dB 2-channel hardware-controlled audio ADC in my design due to PCM 2902 is not recommended for new design. High sampling rate and SNR are…
    • Resolved

  • RE: TAS5766M set on slave mode question

    Hi Peter, Thanks for your support. Q1) What's the feature of Page 01, Register 03 ? I caN NOT find anything in TAS5766M data sheet. Q2) May I use PPC3 to fine tune PCM1862 ? I can NOT find any PCM1862 apps . Q3) How to connect PCM1862 and TAS5766M…

  • About PCM1862 + TAS5766M PPC3 GUI !

    Other Parts Discussed in Thread: PCM1862 , TAS5766M Q1) Our platform is PCM1862 (I2S Master,24.576MHz osc.)+TAS5766M(I2S Slave) without feedback. Who can provide the PPC3 GUI for them ? Q2) PCM1862 audio sources: 1) RADIO Tuner (Si4731) analog…
    • Answered

  • [FAQ] Linux Drivers: Device drivers for AIC31xx/DAC31xx/AIC325x/AIC320x/AIC326x/AIC321x

    Resolved
    Other Parts Discussed in Thread: PCMD3140 , TAA3040 , PCMD3180 , TLV320ADC3101 , TLV320ADC3100 , TLV320AIC26 , TLV320AIC3120 , TLV320AIC3100 , TLV320DAC3101 , TLV320DAC3100 , TLV320AIC3111 , TLV320AIC3110 , TLV320AIC3105 , TLV320AIC3106 , TLV320AIC3107…
    • Resolved

  • RE: TPA3251: PFFB problem and OC protection issue

    Hi Justin The input signal is as below ,pls. refer. When protection hanppen, the CLIP_OTW pin is also going high, but the FAULT pin going low, and TPA3251 shutdown one of the channel or two channel, it can't self clearing, It must be restarted.. Attachment…

Didn't find what you are looking for? Post a new question.