Search tips
Showing 118 results View by: Thread Post Sort by
    Answered

  • PCM5102: PCM5102 & PCM5122 24 bit 96khz LSB audio

    Resolved
    Part Number: PCM5102 Other Parts Discussed in Thread: PCM5122 Tool/software: I have asked a similar question about PCM5122 and got a similar answer (which i was not satisfied with) This table is from PCM510x datasheet and accordingly, 6.144M clock…
    • Resolved
    • Answered

  • PCM5102: PCM5102 Left/Right independent control in HW mode

    Resolved
    Part Number: PCM5102 Other Parts Discussed in Thread: PCM5101 , PCM1798 Tool/software: Hi All, I'm using PCM5102 with H/W conorl mode and I2S format.. as below But at this condition, I can't contorl Left and Right independenlty by Input source.…
    • Resolved

  • PCM5102: PCM5102 vs UDA1334

    TI Thinks Resolved
    Part Number: PCM5102 Tool/software: Hello, I'm an application engineer and I need some help to choose one of your DAC to replace an out of production NXP UDA1334 in an already existent FPGA based project. The NXP UDA1334 is an hardware controlled DAC…
    • Answered

  • PCM5102A: No Sound from I2S PCM5102 DAC

    Resolved
    Part Number: PCM5102A I'm designing an audio board using the DAC PCM5102A. This is my schematic: I have FILTER_SEL and DEMP_SEL solded to GND. LRCK, DIN and BCK routed to an esp32 pin though a 22Ohm resistor. SCK to GND. 3.3VD comes from a buck…
    • Resolved
    • Answered

  • PCM2706C: Can't get audio output from PCM2706+PCM5102 combination

    Resolved
    Part Number: PCM2706C Other Parts Discussed in Thread: OPA1622 , PCM5102 , PCM2706 , , PCM5102A Tool/software: Hello experts, Sorry for bothering you about this problem. I am working on an early stage of a personal audio device, based on PCM2706…
    • Resolved

  • PCM5102: Problem with PIN 11, FLT

    TI Thinks Resolved
    Part Number: PCM5102 Other Parts Discussed in Thread: DIR9001 Tool/software: Hello all, maybe my problem fits in here. I have a small problem with the DAC PCM5102A. The problem is PIN 11 - FLT The DAC is connected to a DIR9001 via the I2S bus…

  • PCM5102: De-emphasis pin operation

    TI Thinks Resolved
    Part Number: PCM5102 Other Parts Discussed in Thread: PCM5142 Can you kindly explain the DEMP pin 10 more fully? If enabled, is it enabled continuously, or only when the emphasis bit 5 is set in the I2S stream? If disabled, it's killed completely…
    • Answered

  • PCM5100A: pin to pin replacement with PCM5102

    Resolved
    Part Number: PCM5100A Other Parts Discussed in Thread: PCM5102 , PCM5100 Hi team, My customer is facing supply situation on PCM5100APWR. Could you please check if PCM5100APWR can be replaced by PCM5102PWR? And are PCM510xA and PCM510x devices…
    • Resolved

  • PCM5102A: What is the difference between PCM5102 and PCM5102A?

    TI Thinks Resolved
    Part Number: PCM5102A Other Parts Discussed in Thread: PCM5102 , Hi TI team, PCM5102 is NRND. What is the difference between PCM5102 and PCM5102A? Thanks Downey Kim.

  • PCM5102: Driving the hardware IO pins

    TI Thinks Resolved
    Part Number: PCM5102 Hello, This is a rather silly question, but when driving IO pins such as XSMT, FLT, DEMP, and FMT is it required that I place a resistor between the pin and the GND / +3.3v? I've assembled a test board and it's not functional…

Didn't find what you are looking for? Post a new question.