Answered

• PTH08T210W: PTH Series UL Approval

  

  Markus Schrodt

  Resolved

  Part Number: PTH08T210W Tool/software: Hi. For the PTH Series, especially the PTH08T210W the datasheet states: Safety Agency Approvals: – UL/IEC/CSA-22.2 60950-1 However I can't find a UL File number on any of the Modules in PTH series. Some state…

  • Resolved

  • over 1 year ago
  • Power management
  • Power management forum

• PTH08T210W: PTH08T210WAH 3D Step File Model

  

  Joey Cichosz

  TI Thinks Resolved

  Part Number: PTH08T210W Tool/software: Can you please generate a PTH08T210WAH 3D Step File Model?

  • over 1 year ago
  • RF & microwave
  • RF & microwave forum

• PTH08T210W: About auto reset time

  

  Sam Wang1

  Part Number: PTH08T210W I use DAC control VoAdj and MCU control inhibit pin. When control system <DAC and MCU> shutdown and Vin keep power-up, I saw Inhibit control signal auto restet from low to high in 300ms.I'd like know if PTH08T210W auto reset in…

  • over 3 years ago
  • Power management
  • Power management forum

• PTH08T210W: PCB Layout

  

  yuichiroiida

  TI Thinks Resolved

  Part Number: PTH08T210W Other Parts Discussed in Thread: TPSM846C23 Could you tell me the recommended board layout including connection of the bypass capacitor when using the PTH08T210W?

  • over 4 years ago
  • Power management
  • Power management forum
Answered

• PTH08T210W: Hiccup MODE

  

  Yeonggi Kwon

  Resolved

  Part Number: PTH08T210W In my circuit, the output seems to go into hiccup mode. The input moves slightly, but I don't know why it goes into hiccup mode. There is almost no output load (300Ohm) and there is no actual overcurrent flow. Are there any…

  • Resolved

  • over 5 years ago
  • Power management
  • Power management forum
Answered

• PTH08T210W: Triming the output voltage

  

  Meng Chan74

  Resolved

  Part Number: PTH08T210W Hi, What is the best way to trim the output voltage(1.0V) by +/-5% ? Can the Vo_adj accept voltage source override, with what drive strength? Thanks, Meng

  • Resolved

  • over 7 years ago
  • Power management
  • Power management forum

• WEBENCH® Tools/PTH08T210W: The differences between PTH08T210WAH and PTH08T210WAD

  

  AndongSun

  Part Number: PTH08T210W Tool/software: WEBENCH® Design Tools Hi, About PTH08T210WA H and PTH08T210WA D , we can't see the differences in the specification on the official website, please help to confirm the specific differences, thanks. …

  • over 6 years ago
  • Power management
  • Power management forum
Answered

• PTH08T210W: ABOUT THE OUPUT CAPACITOR OF PTH08T210

  

  Iven Xu

  Resolved

  Part Number: PTH08T210W Dear moudle expert, Could you please help clarify how to select the output capacitor value for PTH08T210W? dos the Co requirement means for the total capacitor on the same net_work of the PTH08T210W? based on the transient…

  • Resolved

  • over 9 years ago
  • Power management
  • Power management forum

• PTH08T210W: resistor connection to achieve the output voltage transfer function

  

  SIDDHARTH MOHAN

  TI Thinks Resolved

  Part Number: PTH08T210W Hi All, Can you please provide the resistor connection to achieve the output voltage transfer function for the following part. The resistor connection block diagram connecting the output to the error amplifier PTH08T210W

  • over 8 years ago
  • Power management
  • Power management forum
Answered

• Input capacitance sharing between PTH08T210W

  

  WEIMING QIAN

  Resolved

  Other Parts Discussed in Thread: PTH08T210W , PTH08T250W I'm using 8 PTH08T210W/PTH08T250W on a ATCA module to power Xilinx FPGAs with total power of ~300W. The datasheet of these DCDC modules require a minimum input capacitance of 470uF/1000uF. If I…

  • Resolved

  • over 12 years ago
  • Power management
  • Power management forum

Didn't find what you are looking for? Post a new question.