TI E2E support forums
TI E2E support forums
  • User
  • Site
  • Search
  • User
  • E2E™ design support >
  • Forums
    • Amplifiers
    • API solutions
    • Audio
    • Clock & timing
    • Data converters
    • DLP® products
    • Interface
    • Isolation
    • Logic
    • Microcontrollers
    • Motor drivers
    • Power management
    • Processors
    • RF & microwave
    • Sensors
    • Site support
    • Switches & multiplexers
    • Tools
    • Wireless connectivity
    • Archived forums
    • Archived groups
  • Technical articles
  • TI training
    • Tech days
    • Online training
    • Live events
    • Power Supply Design Seminar
  • Getting started
  • 简体中文
  • More
  • Cancel


Search tips
Showing 12,573 results View by: Thread Post Sort by
    Answered
  • RE: CC2500: Receiving sensitivity - 120dbm solution

    TER
    TER
    Resolved
    If they want a 3 km range they should not use CC2400 but a sub 1 GHz product. Look into CC1120 or CC1310 and ask them to look into https://www.ti.com/tool/RF-RANGE-ESTIMATOR to get an estimate for range.
    • over 5 years ago
    • Other wireless
    • Other wireless technologies forum
  • Answered
  • RE: CC2420: Distance Estimation model using RSSI

    FI
    FI
    Resolved
    Hi, You can look at the range estimator excel sheet here and app note here: http://www.ti.com/lit/an/swra479a/swra479a.pdf http://www.ti.com/tool/RF-RANGE-ESTIMATOR regards,
    • over 6 years ago
    • Other wireless
    • Other wireless technologies forum
  • RE: CC2640: Long range operation introduction

    TER
    TER
    Not sure if I follow you: You ask about CC2640 but what you have put a red rectangle around is related to our sub 1-GHz offering (CC2640 is just 2.4 GHz) You can use http://www.ti.com/tool/RF-RANGE-ESTIMATOR to estimate the potential range.
    • over 6 years ago
    • Bluetooth®︎
    • Bluetooth forum
  • Answered
  • RE: LAUNCHXL-CC26X2R1: Antenna CC26X2R1

    TER
    TER
    Resolved
    1) Use http://www.ti.com/tool/RF-RANGE-ESTIMATOR to make an estimate 2) No since that would not be a 50 ohm load. 3) Information about this is in the schematic.
    • over 6 years ago
    • Zigbee & Thread
    • Zigbee & Thread forum
  • RE: CC1120: Poor signal quality without direct line sight.

    TER
    TER
    You can calculate the estimated range by using https://www.ti.com/tool/RF-RANGE-ESTIMATOR For none line of sight the range will be affected by what you have between the sender and receiver. Have you estimated the attenuation you have in the link?
    • over 5 years ago
    • Sub-1 GHz
    • Sub-1 GHz forum
  • extending RF com range with the EZ 430 chrono (868 MHz)

    Stefano Rossi
    Stefano Rossi
    Hi everybody. I need to extend RF coms range between the EZ 430 (868 MHz) chrono and the RF USB device; I need to have devices communicating in a whole big apartment; may someone suggest any RF repeaters? Thanks in advance Stefano
    • over 15 years ago
    • Sub-1 GHz
    • Sub-1 GHz forum
  • RE: CC1352P: CC1352P as collector and CC1352P as sensor can communicate up to what distance(in Kilometers) if power amplifier section is enabled and transmit power is 20 dbM both sides

    Ammar N
    Ammar N
    Hey Haricharan, Your range depends on which data rate/PHY you're operating on as well as your hardware configuration. Simplelink long range mode (5kbps) provides the longest range. You may also use our range estimator spreadsheet to estimate the range…
    • over 6 years ago
    • Sub-1 GHz
    • Sub-1 GHz forum
  • Answered
  • RE: CC2652R: ZED packets unsuccessfully sent but works fine when I put my finger on the antenna

    Ryan Brown1
    Ryan Brown1
    Resolved
    Please refer to the https://www.ti.com/tool/RF-RANGE-ESTIMATOR but it will also depend on output TX power, environment/channel noise, Wi-Fi/BLE interference, and physical barriers (such as walls). Regards, Ryan
    • over 5 years ago
    • Zigbee & Thread
    • Zigbee & Thread forum
  • RE: CC1310: Behavior of CC1310/CC1312R on rural forest / dense vegetation environment

    YiKai Chen
    YiKai Chen
    Don't read any related information about using TI 15.4 stack under such environment but you can try to use TI RF-RANGE-ESTIMATOR to do some estimation. By the way, TI 15.4 stack doesn't support mesh capability for now and you can use Wi-SUN, which support…
    • over 5 years ago
    • Sub-1 GHz
    • Sub-1 GHz forum
  • RE: LAUNCHXL-CC13-90: Range extender

    Vegard H
    Vegard H
    Hi Can you describe more how you are sending the data? What phy, data rate, frequecy, etc. Have you looked at the range estimation tool to calculate expected range? www.ti.com/.../RF-RANGE-ESTIMATOR Vegard
    • over 5 years ago
    • Sub-1 GHz
    • Sub-1 GHz forum
<>

Didn't find what you are looking for? Post a new question.

  • Ask a new question