TI E2E support forums
TI E2E support forums
  • User
  • Site
  • Search
  • User
  • E2E™ design support >
  • Forums
    • Amplifiers
    • API solutions
    • Audio
    • Clock & timing
    • Data converters
    • DLP® products
    • Interface
    • Isolation
    • Logic
    • Microcontrollers
    • Motor drivers
    • Power management
    • Processors
    • RF & microwave
    • Sensors
    • Site support
    • Switches & multiplexers
    • Tools
    • Wireless connectivity
    • Archived forums
    • Archived groups
  • Technical articles
  • TI training
    • Tech days
    • Online training
    • Live events
    • Power Supply Design Seminar
  • Getting started
  • 简体中文
  • More
  • Cancel


Search tips
Showing 12,573 results View by: Thread Post Sort by
  • RE: CC1310: sub 1G rf issue

    TER
    TER
    CC1310 only supports up to 4 Mbps. I would recommend using www.ti.com/.../RF-RANGE-ESTIMATOR to estimate range. 60 km difficult to reach even with low datarates (a few kbps) and with a range extender, meaning that you should look into if your spec is…
    • over 7 years ago
    • Sub-1 GHz
    • Sub-1 GHz forum
  • RE: CC1101: CC1101(ACTIVE) Low-Power Sub-1GHz RF Transceiver

    TER
    TER
    You can use www.ti.com/.../rf-range-estimator to estimate range. Note that none of our transceivers are radiation hardened.
    • over 7 years ago
    • Sub-1 GHz
    • Sub-1 GHz forum
  • RE: CC1312R7: WI-SUN NETWORK IN QUITO - ECUADOR

    Sid
    Sid
    Hi Mario, Thank you for your interest in our WiSUN solution. 1. The WiSUN protocol is designed for interoperability and we do attend WiSUN Alliance's inter op events. It should be possible to possible to communicate with WiSUN boards of different…
    • over 4 years ago
    • Sub-1 GHz
    • Sub-1 GHz forum
  • RE: LAUNCHXL-CC1352P: Comms range test

    TER
    TER
    You can use www.ti.com/.../rf-range-estimator to estimate range. - How are the LPs positioned when doing this test? Placed on what, how high above ground? - If you have the TX side turned off, how high is the background noise if you set the RX side…
    • over 7 years ago
    • Sub-1 GHz
    • Sub-1 GHz forum
  • RE: CC1352R: Best Settings for Wideband Range

    TER
    TER
    This tool: https://www.ti.com/tool/RF-RANGE-ESTIMATOR can be used to estimate the range for different phy/ predefined settings. Deviation vs symbolrate: The modem is designed to give best performance for a modulation index equal to 0.5 to 1. Too high…
    • over 4 years ago
    • Sub-1 GHz
    • Sub-1 GHz forum
  • RE: LAUNCHXL-CC26X2R1: Max range of Zigbee with output power 5dbm

    YiKai Chen
    YiKai Chen
    Try to use RF-RANGE-ESTIMATOR to estimate the distance.
    • over 8 years ago
    • Zigbee & Thread
    • Zigbee & Thread forum
  • Answered
  • RE: CC1352P: Regarding CC1352P Stack and Line of sight range

    RGW
    RGW
    Resolved
    Hi, Good to hear that you are looking at the CC1352P for your new project. The landing page for all the CC1352P is available at: www.ti.com/.../CC1352P For the hardware section, please follow one of the reference designs: 20 dBm PA for 868/915…
    • over 5 years ago
    • Sub-1 GHz
    • Sub-1 GHz forum
  • RE: CCS/LAUNCHXL-CC13-90: Maximum range of TI 15.4 Stack on CC13-90

    PM
    PM
    Hi, You can use our Range Estimator, which is available on our website. The following is the link. Yes, this applies to 802.15.4 also. www.ti.com/.../RF-RANGE-ESTIMATOR Estimator&tisearch=Search-EN-Everything Thanks, PM
    • over 7 years ago
    • Sub-1 GHz
    • Sub-1 GHz forum
  • Answered
  • RE: LAUNCHXL-CC26X2R1: BLE multi role central example not connecting over 5 meter device?

    Nathan Block
    Nathan Block
    Resolved
    Depending on the transmit power and receiver sensitivity of your devices, this may be possible. It will be highly dependent on the environment you're in as well. You might find the RF range estimation tool useful for this calculation as a starting point…
    • over 5 years ago
    • Bluetooth®︎
    • Bluetooth forum
  • RE: CC1310: About the Range on the custom CC1310

    TER
    TER
    Please do the measurements suggested in http://www.ti.com/lit/an/swra603/swra603.pdf .and report back. Also have you checked the background noise where you are testing since this is impacting the sensitivity (see http://www.ti.com/tool/rf-range-estimator…
    • over 7 years ago
    • Sub-1 GHz
    • Sub-1 GHz forum
<>

Didn't find what you are looking for? Post a new question.

  • Ask a new question